Agilent Technologies InfiniiVision 5000 Series Programmer's Manual page 780

Index
fall time measurement, 272, 282
falling edge, 419
Fast Fourier Transform (FFT) functions, 230,
231, 242, 243, 244, 576
FF values in waveform data, 509
FFT (Fast Fourier Transform) functions, 230,
231, 242, 243, 244, 576
FFT (Fast Fourier Transform) operation, 237,
521
FFT math function, 168
fifty ohm impedance, disable setting,
FILename commands, 541
filename for hardcopy, 580
filename for recall, 352
filename for save, 359
filter for frequency reject, 442
filter for high frequency reject, 415
filter for noise reject, 418
filter used to limit bandwidth, 192,
filters to Fast Fourier Transforms,
fine horizontal adjustment (vernier),
fine vertical adjustment (vernier),
finish pending device operations,
first point displayed, 531
FLATtop window for amplitude
measurements, 244
format, 511, 516
FORMat commands, 541
format for block data, 107
format for generic video, 480, 484
format for hardcopy, 578, 581
format for image, 363
format for waveform data, 370
FormattedIO488 object, 45
formfeed for hardcopy, 246, 250
frame, 478
frame counters (CAN), error, 375
frame counters (CAN), overload,
frame counters (CAN), reset, 377
frame counters (CAN), total, 378
frame counters (UART), error, 386
frame counters (UART), reset, 387
frame counters (UART), Rx frames,
frame counters (UART), Tx frames,
framing, 473
FRAMing commands, 541
frequency measurement, 43, 272,
frequency resolution, 244
frequency span of display, 243
frequency versus dB, 230
front panel mode, 421
front panel Single key, 158
front panel Stop key, 160
front-panel lock, 395
full-scale horizontal time, 404, 409
full-scale vertical axis defined, 238
function, 162, 231, 232, 236, 237, 238, 239,
240, 242, 243, 244, 576, 577
FUNCtion commands, 228
function memory, 159
function turned on or off, 577
functions, 521
780
functions, erasing,
G
g(t) source, first input channel,
g(t) source, math operation,
g(t) source, second input channel,
gateway IP, 33
general trigger commands,
GENeric, 480,
396
generic video format, 480,
glitch duration,
glitch qualifier,
glitch source,
GLITch trigger commands,
glitch trigger duration,
glitch trigger polarity,
glitch trigger source,
220
GOFT commands,
244
GPIB interface, 33,
407
graphics, 211
207
graticule area for hardcopy print,
108
graticule area for saved image,
graticule colors, invert for hardcopy, 251,
graticule colors, invert for image,
graticule data,
grayscale palette for hardcopy,
grayscale palette for image,
grayscaling on hardcopy,
greater than qualifier,
greater than time, 434, 438, 446,
GREaterthan commands,
H
HANNing window for frequency
resolution,
376
hardcopy, 155,
HARDcopy commands,
hardcopy device,
hardcopy factors, 249,
hardcopy filename,
388
hardcopy format, 578,
389
hardcopy formfeed,
hardcopy grayscale,
hardcopy invert graticule colors, 251,
283
hardcopy layout,
hardcopy palette,
hardcopy print, area,
hardcopy printer driver,
hardware event condition register,
Hardware Event Condition Register
(:HWERegister:CONDition),
Hardware Event Condition Register
(:OPERegister:CONDition),
Hardware Event Enable Register
(HWEenable),
hardware event event register,
Hardware Event Event Register
(:HWERegister[:EVENt]), 138,
header, 660
131
234
233
235
414
484
484
451
450
452
445
446
449
446
542
34
247
361
583
364
211
253
365
582
450
451
542
244
246
245
579
362
580
581
250
582
583
252
253
247
584
136
136
643
134
138
642
Agilent InfiniiVision 5000 Series Oscilloscopes Programmer's Guide
high-frequency reject filter, 415,
high-resolution acquisition type,
hold until operation complete, 108
holdoff time, 416
holes in waveform data, 509
horizontal adjustment, fine (vernier),
horizontal position, 408
horizontal scale, 406, 410
horizontal scaling, 516
horizontal time, 404, 409, 587
hostname, 33
HWEenable (Hardware Event Enable
Register), 134
HWERegister:CONDition (Hardware Event
Condition Register), 136, 643
HWERegister[:EVENt] (Hardware Event Event
Register), 138, 642
I
I/O softkey, 33, 34
I1080L50HZ, 480, 484
I1080L60HZ, 480, 484
ID commands, 543
id mode, 427
identification number, 106
identification of options, 109
identifier, 426
identifier, LIN, 463
idle until operation complete, 108
IDN (Identification Number), 106
IEEE 488.2 standard, 99
IGColors commands, 543
IIC address, 454
IIC clock, 457
IIC commands, 543
IIC data, 455, 458
IIC data 2, 456
IIC serial decode address field size,
IIC trigger commands, 453
IIC trigger qualifier, 459
IIC trigger type, 460
IMAGe commands, 543
image format, 363
image invert graticule colors, 364
image memory, 159, 216
image palette, 365
image, recall, 353
image, save, 360
image, save with inksaver, 364
impedance, 195
IMPedance commands, 543
impedance for external trigger input, 221,
infinity representation, 677
initialization, 42, 45
initialize, 111
initialize label list, 214
initiate acquisition, 132
inksaver, save image with, 364
input, 221, 574
input coupling for channels, 193
input impedance for channels, 195,
442
164
407
381
574
570