Danfoss VLT AutomationDrive FC 300 Programming Manual page 193

3 Parameter descriptions
[10] Select preset ref 0
[11] Select preset ref 1
3
[12] Select preset ref 2
[13] Select preset ref 3
[14] Select preset ref 4
[15] Select preset ref 5
[16] Select preset ref 6
[17] Select preset ref 7
[18] Select ramp 1
[19] Select ramp 2
[20] Select ramp 3
[21] Select ramp 4
[22] Run
[23] Run reverse
[24] Stop
[25] Qstop
[26] Dcstop
[27] Coast
[28] Freeze output
[29] Start timer 0
[30] Start timer 1
[31] Start timer 2
[32] Set digital out A low
[33] Set digital out B low
[34] Set digital out C low
192
If the set-up is changed, it will merge with other set-up commands coming from either the digital
inputs or via a fieldbus.
Select preset reference 0 [10] – selects preset reference 0.
If the active preset reference is changed, it will merge with other preset reference commands com-
ing from either the digital inputs or via a fieldbus.
Select preset reference 1
[11] – selects preset reference 1.
If the active preset reference is changed, it will merge with other preset reference commands com-
ing from either the digital inputs or via a fieldbus.
Select preset reference 2 [12] – selects preset reference 2.
If the active preset reference is changed, it will merge with other preset reference commands com-
ing from either the digital inputs or via a fieldbus.
Select preset reference 3
[13] – selects preset reference 3.
If the active preset reference is changed, it will merge with other preset reference commands com-
ing from either the digital inputs or via a fieldbus.
Select preset reference 4
[14] – selects preset reference 4.
If the active preset reference is changed, it will merge with other preset reference commands com-
ing from either the digital inputs or via a fieldbus.
Select preset reference 5
[15] – selects preset reference 5.
If the active preset reference is changed, it will merge with other preset reference commands com-
ing from either the digital inputs or via a fieldbus.
Select preset reference 6
[16] – selects preset reference 6.
If the active preset reference is changed, it will merge with other preset reference commands com-
ing from either the digital inputs or via a fieldbus.
Select preset reference 7 [17] - selects preset reference 7.
If the active preset reference is changed, it will merge with other preset reference commands com-
ing from either the digital inputs or via a fieldbus.
Select ramp 1
[18] - selects ramp 1.
Select ramp 2 [19] - selects ramp 2.
Select ramp 3 [20] - selects ramp 3.
Select ramp 4
[21] - selects ramp 4.
Run
[22] - issues a start command to the frequency converter.
Run reverse [23] - issues a start reverse command to the frequency converter.
Stop [24] - issues a stop command to the frequency converter.
Qstop
[25] - issues a quick stop command to the frequency converter.
Dcstop
[26] - issues a DC stop command to the frequency converter.
Coast [27] - the frequency converter coasts immediately. All stop commands including the coast
command stop the SLC.
Freeze output
[28] - freezes the output frequency of the frequency converter.
Start timer 0
[29] - starts timer 0, see par. 13-20 for further description.
Start timer 1 [30] - starts timer 1, see par. 13-20 for further description.
Start timer 2 [31] - starts timer 2, see par. 13-20 for further description.
Set digital output A low
[32] - any output with SL output A will be low.
Set digital output B low
[33] - any output with SL output B will be low.
Set digital output C low [34] - any output with SL output Cwill be low.
®
MG.33.M8.02 - VLT is a registered Danfoss trademark
FC 300 Programming Guide