Danfoss VLT AutomationDrive FC 300 Programming Manual page 108

FC 300 Programming Guide
[41] Below reference, low
[42] Above ref, high
[43] Extended PID Limit
[45] Bus ctrl.
[46] Bus ctrl, 1 if timeout
[47] Bus ctrl, 0 if timeout
[51] MCO controlled
[60] Comparator 0
[61] Comparator 1
[62] Comparator 2
[63] Comparator 3
[64] Comparator 4
[65] Comparator 5
[70] Logic rule 0
[71] Logic rule 1
[72] Logic rule 2
[73] Logic rule 3
[74] Logic rule 4
[75] Logic rule 5
[80] SL digital output A
[81] SL digital output B
[82] SL digital output C
[83] SL digital output D
[84] SL digital output E
Active when actual speed is below speed reference setting.
Active when actual speed is above speed reference setting.
Controls digital output/relay via bus. The state of the output is set in par. 5-90 'Digital & Relay Bus
Control'. The output state is retained in the event of bus time-out.
Controls output via bus. The state of the output is set in par. 5-90
the event of bus time-out the output state is set high (On).
Controls output via bus. The state of the output is set in par. 5-90
the event of bus time-out the output state is set low (Off).
Active when a MCO 302 or MCO 305 is connected. The output is controlled from option.
See par. group 13-1* (Smart Logic Control). If Comparator 0 in SLC is TRUE, the output will go high.
Otherwise, it will be low.
See par. group 13-1* (Smart Logic Control). If Comparator 1 in SLC is TRUE, the output will go high.
Otherwise, it will be low.
See par. group 13-1* (Smart Logic Control). If Comparator 2 in SLC is TRUE, the output will go high.
Otherwise, it will be low.
See par. group 13-1* (Smart Logic Control). If Comparator 3 in SLC is TRUE, the output will go high.
Otherwise, it will be low.
See par. group 13-1* (Smart Logic Control). If Comparator 4 in SLC is TRUE, the output will go high.
Otherwise, it will be low.
See par. group 13-1* (Smart Logic Control). If Comparator 5 in SLC is TRUE, the output will go high.
Otherwise, it will be low.
See par. group 13-4*(Smart Logic Control). If Logic Rule 0 in SLC is TRUE, the output will go high.
Otherwise, it will be low.
See par. group 13-4*(Smart Logic Control). If Logic Rule 1 in SLC is TRUE, the output will go high.
Otherwise, it will be low.
See par. group 13-4*(Smart Logic Control). If Logic Rule 2 in SLC is TRUE, the output will go high.
Otherwise, it will be low.
See par. group 13-4*(Smart Logic Control). If Logic Rule 3 in SLC is TRUE, the output will go high.
Otherwise, it will be low.
See par. group 13-4*(Smart Logic Control). If Logic Rule 4 in SLC is TRUE, the output will go high.
Otherwise, it will be low.
See par. group 13-4*(Smart Logic Control). If Logic Rule 5 in SLC is TRUE, the output will go high.
Otherwise, it will be low.
See par. 13-52 'Smart Logic Control Action'. Output A is low on Smart Logic Action [32]. Output A
is high on Smart Logic Action [38].
See par. 13-52 'Smart Logic Control Action'. Output B is low on Smart Logic Action [33]. Output B
is high on Smart Logic Action [39].
See par. 13-52 'Smart Logic Control Action'. Output C is low on Smart Logic Action [34]. Output C
is high on Smart Logic Action [40].
See par. 13-52 'Smart Logic Control Action'. Output D is low on Smart Logic Action [35]. Output D
is high on Smart Logic Action [41]
See par. 13-52 'Smart Logic Control Action'. Output E is low on Smart Logic Action [36]. Output E
is high on Smart Logic Action [42].
®
MG.33.M8.02 - VLT is a registered Danfoss trademark
3 Parameter descriptions
Digital & Relay Bus Control
. In
Digital & Relay Bus Control . In
107
3