Danfoss VLT AQUA Drive FC 202 Programming Manual page 43

Parameter Description
1-03 Torque Characteristics
Option: Function:
but if the motor power factor cos phi requires
tuning, an AMA function can be carried out
using parameter 1-29 Automatic Motor Adaptation
(AMA). It is rarely necessary to adjust the motor
power factor parameter manually.
NOTICE
Parameter 1-03 Torque Characteristics has no effect when
parameter 1-10 Motor Construction = [1] PM, non-salient
SPM.
1-04 Overload Mode
Select the torque level in overload mode.
Option: Function:
[0] High torque Allows up to 160% overtorque for
undersized motors.
[1] Normal torque Allows up to 110% overtorque.
*
1-06 Clockwise Direction
Option: Function:
NOTICE
This parameter cannot be adjusted while
the motor is running.
This parameter defines the term clockwise
corresponding to the LCP direction arrow. Used for
easy change of direction of shaft rotation without
swapping motor wires.
[0] Normal The motor shaft turns in clockwise direction when
*
the frequency converter is connected U⇒U, V⇒V,
and W⇒W to the motor.
[1] Inverse Motor shaft turns in counterclockwise direction
when the frequency converter is connected U⇒U,
V⇒V, and W⇒W to the motor.
3.3.2 1-1* Motor Selection
NOTICE
This parameter group cannot be adjusted while the
motor is running.
The following parameters are active depending on the
setting in parameter 1-10 Motor Construction.
[0]
Parameter 1-10 Motor Asynchro
Construction -
nous
Parameter 1-00 Config-
x
uration Mode
MG20OB02
Programming Guide
[1] PM [2] PM
[3]
Motor Motor
SynRM
non- Salient
Motor
salient IPM
x x x
Danfoss A/S © 05/2018 All rights reserved.
[0]
Parameter 1-10 Motor Asynchro
Construction -
nous
Parameter 1-03 Torque
x
Characteristics
Parameter 1-06 Clockwi
x
se Direction
Parameter 1-14 Dampi
–
ng Gain
Parameter 1-15 Low
Speed Filter Time –
Const.
Parameter 1-16 High
Speed Filter Time –
Const.
Parameter 1-17 Voltage
–
filter time const.
Parameter 1-20 Motor
x
Power [kW]
Parameter 1-21 Motor
x
Power [HP]
Parameter 1-22 Motor
x
Voltage
Parameter 1-23 Motor
x
Frequency
Parameter 1-24 Motor
x
Current
Parameter 1-25 Motor
x
Nominal Speed
Parameter 1-26 Motor
–
Cont. Rated Torque
Parameter 1-28 Motor
x
Rotation Check
Parameter 1-29 Autom
atic Motor Adaptation x
(AMA)
Parameter 1-30 Stator
x
Resistance (Rs)
Parameter 1-31 Rotor
x
Resistance (Rr)
Parameter 1-35 Main
x
Reactance (Xh)
Parameter 1-37 d-axis
–
Inductance (Ld)
Parameter 1-39 Motor
x
Poles
Parameter 1-40 Back
–
EMF at 1000 RPM
Parameter 1-44 d-axis
–
Inductance Sat. (LdSat)
Parameter 1-45 q-axis
–
Inductance Sat. (LqSat)
Parameter 1-46 Positio
–
n Detection Gain
[1] PM [2] PM
[3]
Motor Motor
SynRM
non- Salient
Motor
salient IPM
– - -
x x x
x x x
x x x
x x x
x x x
– – –
– – –
– – –
– – –
x x x
x x x
x x x
x x x
x x x
x x x
– – –
– – –
x x x
x x x
x x –
– – x
– x –
x x x
41
3 3