Danfoss VLT AQUA Drive FC 202 Programming Manual page 83

Parameter Description
NOTICE
Options [4] PTC 1 Alarm to [9] PTC 1 & Relay W/A are only
available when the MCB 112 is connected.
NOTICE
Selecting Auto Reset/Warning enables automatic restart
of the frequency converter.
Function Num PTC
-
ber
No Function [0] –
Safe Torque Off [1]* –
Alarm
Safe Torque Off [3] –
Warning
PTC 1 Alarm [4] PTC 1 Safe Torque
Off [A71]
PTC 1 Warning [5] PTC 1 Safe Torque
Off [W71]
PTC 1 & Relay A [6] PTC 1 Safe Torque
Off [A71]
PTC 1 & Relay W [7] PTC 1 Safe Torque
Off [W71]
PTC 1 & Relay A/W [8] PTC 1 Safe Torque
Off [A71]
PTC 1 & Relay W/A [9] PTC 1 Safe Torque
Off [W71]
Table 3.14 Overview of Functions, Alarms, and Warnings
W means warning and A means alarm. For further information, see
Alarms and Warnings in chapter 5 Troubleshooting.
A dangerous failure related to Safe Torque Off issues alarm
72, Dangerous failure.
Refer to Table 5.1.
5-20 Terminal X46/1 Digital Input
This parameter is related to the digital input on VLT
Relay Card MCB 113. The parameter contains all options and
functions listed in parameter group 5-1* Digital Inputs except for
option [32] Pulse input.
5-21 Terminal X46/3 Digital Input
This parameter is related to the digital input on VLT
Relay Card MCB 113. The parameter contains all options and
functions listed in parameter group 5-1* Digital Inputs except for
option [32] Pulse input.
5-22 Terminal X46/5 Digital Input
This parameter is related to the digital input on VLT
Relay Card MCB 113. The parameter contains all options and
functions listed in parameter group 5-1* Digital Inputs except for
option [32] Pulse input.
MG20OB02
Programming Guide
5-23 Terminal X46/7 Digital Input
This parameter is related to the digital input on VLT
Relay Card MCB 113. The parameter contains all options and
functions listed in parameter group 5-1* Digital Inputs except for
option [32] Pulse input.
5-24 Terminal X46/9 Digital Input
This parameter is related to the digital input on VLT
Relay Card MCB 113. The parameter contains all options and
functions listed in parameter group 5-1* Digital Inputs except for
Relay
option [32] Pulse input.
5-25 Terminal X46/11 Digital Input
–
This parameter is related to the digital input on VLT
Safe Torque Off
Relay Card MCB 113. The parameter contains all options and
[A68]
functions listed in parameter group 5-1* Digital Inputs except for
Safe Torque Off
option [32] Pulse input.
[W68]
–
5-26 Terminal X46/13 Digital Input
This parameter is related to the digital input on VLT
–
Relay Card MCB 113. The parameter contains all options and
functions listed in parameter group 5-1* Digital Inputs except for
Safe Torque Off
option [32] Pulse input.
[A68]
Safe Torque Off
3.7.3 5-3* Digital Outputs
[W68]
Safe Torque Off
Parameters for configuring the output functions for the
[W68]
output terminals. The 2 solid-state digital outputs are
Safe Torque Off
common for terminals 27 and 29. Set the I/O function for
[A68]
terminal 27 in parameter 5-01 Terminal 27 Mode and set the
I/O function for terminal 29 in parameter 5-02 Terminal 29
Mode.
NOTICE
These parameters cannot be adjusted while the motor is
running.
®
Extended
[0] No operation
[1] Control ready
[2] Drive ready
®
Extended
[3] Drive ready/
remote
control
[4] Standby/no
warning
®
Extended
[5] Running
[6] Running/no
warning
Danfoss A/S © 05/2018 All rights reserved.
®
Extended
®
Extended
®
Extended
®
Extended
The digital outputs can be programmed
with these functions:
Default for all digital outputs and relay
outputs.
The control board receives supply voltage.
The frequency converter is ready for
operation and applies a supply signal on
the control board.
The frequency converter is ready for
operation and is in auto-on mode.
The frequency converter is ready for
operation. No start or stop command has
been given (start/disable). There are no
warnings.
Motor is running.
The output speed is higher than the speed
set in parameter 1-81 Min Speed for
3 3
81