Danfoss VLT AQUA Drive FC 202 Programming Manual page 117

Parameter Description
13-02 Stop Event
Option: Function:
Select the boolean (true or false) input
to deactivate smart logic control.
[0] False Enters the fixed value of false in the
logic rule.
[1] True Enters the fixed value of true in the
logic rule.
[2] Running See parameter group 5-3* Digital
Outputs for further description.
[3] In range See parameter group 5-3* Digital
Outputs for further description.
[4] On reference See parameter group 5-3* Digital
Outputs for further description.
[5] Torque limit See parameter group 5-3* Digital
Outputs for further description.
[6] Current Limit See parameter group 5-3* Digital
Outputs for further description.
[7] Out of current See parameter group 5-3* Digital
range Outputs for further description.
[8] Below I low See parameter group 5-3* Digital
Outputs for further description.
[9] Above I high See parameter group 5-3* Digital
Outputs for further description.
[10] Out of speed
range
[11] Below speed low See parameter group 5-3* Digital
Outputs for further description.
[12] Above speed high See parameter group 5-3* Digital
Outputs for further description.
[13] Out of feedb. See parameter group 5-3* Digital
range Outputs for further description.
[14] Below feedb. low See parameter group 5-3* Digital
Outputs for further description.
[15] Above feedb. high See parameter group 5-3* Digital
Outputs for further description.
[16] Thermal warning See parameter group 5-3* Digital
Outputs for further description.
[17] Mains out of See parameter group 5-3* Digital
range Outputs for further description.
[18] Reversing See parameter group 5-3* Digital
Outputs for further description.
[19] Warning See parameter group 5-3* Digital
Outputs for further description.
[20] Alarm (trip) See parameter group 5-3* Digital
Outputs for further description.
[21] Alarm (trip lock) See parameter group 5-3* Digital
Outputs for further description.
MG20OB02
Programming Guide
13-02 Stop Event
Option:
[22] Comparator 0
[23] Comparator 1
[24] Comparator 2
[25] Comparator 3
[26] Logic rule 0
[27] Logic rule 1
[28] Logic rule 2
[29] Logic rule 3
[30] SL Time-out 0
[31] SL Time-out 1
[32] SL Time-out 2
[33] Digital input DI18
[34] Digital input DI19
[35] Digital input DI27
[36] Digital input DI29
[37] Digital input DI32
[38] Digital input DI33
[39] Start command
[40] Drive stopped
[41] Reset Trip
[42] Auto Reset Trip
Danfoss A/S © 05/2018 All rights reserved.
Function:
Use the result of comparator 0 in the
logic rule.
Use the result of comparator 1 in the
logic rule.
Use the result of comparator 2 in the
logic rule.
Use the result of comparator 3 in the
logic rule.
Use the result of logic rule 0 in the
logic rule.
Use the result of logic rule 1 in the
logic rule.
Use the result of logic rule 2 in the
logic rule.
Use the result of logic rule 3 in the
logic rule.
Use the result of timer 0 in the logic
rule.
Use the result of timer 1 in the logic
rule.
Use the result of timer 2 in the logic
rule.
Use the value of DI18 in the logic rule
(High = true).
Use the value of DI19 in the logic rule
(High = true).
Use the value of DI27 in the logic rule
(High = true).
Use the value of DI29 in the logic rule
(High = true).
Use the value of DI32 in the logic rule
(High = true).
Use the value of DI33 in the logic rule
(High = true).
This event is true if the frequency
converter is started (either via digital
input, fieldbus or other).
This event is true if the frequency
converter is stopped or coasted (either
via digital input, fieldbus or other).
This event is true if the frequency
converter is tripped (but not trip-
locked) and [Reset] is pressed.
This event is true if the frequency
converter is tripped (but not trip-
locked) and an automatic reset is
issued.
3 3
115