Danfoss VLT AQUA Drive FC 202 Programming Manual page 106

Parameter Description
8-17 Configurable Alarm and Warningword
Array [16]
Select the meaning of a specific bit in the configurable alarm
and warning word. The word has 16 bits (0–15).
Option:
3 3
[9]
[10]
[11]
[12]
[13]
[14]
[17]
[19]
[23]
[24]
[25]
[26]
[27]
[28]
[29]
[30]
[31]
[32]
[34]
[36]
[40]
[41]
[45]
[47]
[58]
[59]
[60]
[61]
[62]
[64]
[65]
[66]
[68]
[73]
[76]
[77]
[163]
[165]
[10002]
[10004]
[10007]
[10008]
[10009]
[10010]
[10011]
[10012]
[10013]
[10014]
[10016]
104
Inverter overloaded warning
Motor ETR overtemp warning
Motor thermistor overtemp warning
Torque limit warning
Over current warning
Earth fault warning
Controlword timeout warning
Discharge temp high warning
Internal fans warning
External fans warning
Brake resistor short circuit warning
Brake powerlimit warning
Brake chopper short circuit warning
Brake check warning
Heatsink temperature warning
Motor phase U warning
Motor phase V warning
Motor phase W warning
Fieldbus communication warning
Mains failure warning
T27 overload warning
T29 overload warning
Earth fault 2 warning
24V supply low warning
AMA internal fault warning
Current limit warning
External interlock warning
Feedback error warning
Frequency max warning
Voltage limit warning
Controlboard overtemp warning
Heatsink temp low warning
Safe stop warning
Safe stop autorestart warning
Power unit setup warning
Reduced powermode warning
ATEX ETR cur limit warning
ATEX ETR freq limit warning
Live zero error alarm
Mains phase loss alarm
DC overvoltage alarm
DC undervoltage alarm
Inverter overload alarm
ETR overtemperature alarm
Thermistor overtemp alarm
Torque limit alarm
Overcurrent alarm
Earth fault alarm
Short circuit alarm
Danfoss A/S © 05/2018 All rights reserved.
®
VLT AQUA Drive FC 202
8-17 Configurable Alarm and Warningword
Array [16]
Select the meaning of a specific bit in the configurable alarm
and warning word. The word has 16 bits (0–15).
Function: Option:
[10017]
[10026]
[10027]
[10028]
[10029]
[10030]
[10031]
[10032]
[10033]
[10034]
[10036]
[10037]
[10038]
[10039]
[10045]
[10046]
[10047]
[10048]
[10049]
[10060]
[10061]
[10063]
[10065]
[10067]
[10068]
[10069]
[10073]
[10074]
[10079]
[10081]
[10082]
[10090]
[10091]
[10164]
[10166]
3.9.3 8-3* FC Port Settings
8-30 Protocol
Option:
[0] FC
[1] FC MC
CTW timeout alarm
Brake powerlimit alarm
Brakechopper shortcircuit alarm
Brake check alarm
Heatsink temp alarm
Phase U missing alarm
Phase V missing alarm
Phase W missing alarm
Inrush fault alarm
Fieldbus com faul alarm
Mains failure alarm
Phase imbalance alarm
Internal fault
Heatsink sensor alarm
Earth fault 2 alarm
Powercard supply alarm
24V supply low alarm
1.8V supply low alarm
Speed limit alarm
Ext interlock alarm
Feedback error alarm
Mech brake low alarm
Controlboard overtemp alarm
Option config changed alarm
Safe stop alarm
Powercard temp alarm
Safestop auto restart alarm
PTC thermistor alarm
Illegal PS config alarm
CSIV corrupt alarm
CSIV param error alarm
Feedback monitor alarm
AI54 settings alarm
ATEX ETR current lim alarm
ATEX ETR freq limit alarm
Function:
Protocol selection for the integrated FC
(standard) port (RS485) on the control card.
Communication according to the FC protocol
as described in RS485 Installation and Set-up in
the relevant design guide.
Same as [0] FC but to be used when
downloading SW to the frequency converter or
uploading dll file (covering information
Function:
MG20OB02