Danfoss VLT AQUA Drive FC 202 Programming Manual page 33

Parameter Description
0-20 Display Line 1.1 Small
Option: Function:
[1613] Frequency Motor frequency, that is the output
frequency from the frequency converter
in Hz.
[1614] Motor Current Phase current of the motor measured as
effective value.
[1615] Frequency [%] Motor frequency, that is the output
frequency from the frequency converter
in percent.
[1616] Torque [Nm] Present motor load as a percentage of
the rated motor torque.
[1617] Speed [RPM] Speed in RPM (revolutions per minute),
that is the motor shaft speed in closed
*
loop based on the entered motor
nameplate data, the output frequency,
and the load on the frequency
converter.
[1618] Motor Thermal Thermal load on the motor calculated
by the ETR function. See also parameter
group 1-9* Motor Temperature.
[1619] KTY sensor
temperature
[1620] Motor Angle
[1622] Torque [%] Shows the actual torque produced in
percentage.
[1625] Torque [Nm]
High
[1630] DC Link DC-link voltage in the frequency
Voltage converter.
[1632] Brake Energy /s Present brake power transferred to an
external brake resistor.
Shows an instant value.
[1633] Brake Brake power transferred to an external
Energy /2 min brake resistor. The average power is
calculated continuously for the most
recent 120 s.
[1634] Heatsink Temp. Present heat sink temperature of the
frequency converter. The cutout limit is
95 ±5 °C. Cutting back in occurs at 70
±5 °C.
[1635] Inverter Percentage load of the inverters.
Thermal
[1636] Inv. Nom. Nominal current of the frequency
Current converter.
[1637] Inv. Max. Maximum current of the frequency
Current converter.
[1638] SL Controller State of the event executed by the
State control.
[1639] Control Card Temperature of the control card.
Temp.
MG20OB02
Programming Guide
0-20 Display Line 1.1 Small
Option:
[1650]
[1651]
[1652]
[1653]
[1660]
[1661]
[1662]
[1663]
[1664]
[1665]
[1666]
[1667]
[1668]
[1669]
[1670]
[1671]
[1672]
[1673]
[1674]
[1675]
Danfoss A/S © 05/2018 All rights reserved.
Function:
External Sum of the external reference as a
Reference percentage, that is the sum of analog,
pulse, and bus.
Pulse
Reference
Feedback [Unit] Signal value in units from the
programmed digital inputs.
Digi Pot View the contribution of the digital
Reference potentiometer to the actual reference
feedback.
Digital Input Shows the status of the digital inputs.
Signal low=0, signal high=1.
Regarding order, see
parameter 16-60 Digital Input. Bit 0 is at
the extreme right.
Terminal 53 Setting of input terminal 53. Current=0,
Switch Setting voltage=1.
Analog Input Actual value at input 53 either as a
53 reference or protection value.
Terminal 54 Setting of input terminal 54. Current=0,
Switch Setting voltage=1.
Analog Input Actual value at input 54 either as
54 reference or protection value.
Analog Output Actual value at output 42 in mA. Use
42 [mA] parameter 6-50 Terminal 42 Output to
select the variable to be show in output
42.
Digital Output Binary value of all digital outputs.
[bin]
Freq. Input #29 Actual value of the frequency applied at
[Hz] terminal 29 as a pulse input.
Freq. Input #33 Actual value of the frequency applied at
[Hz] terminal 33 as a pulse input.
Pulse Output Actual value of pulses applied to
#27 [Hz] terminal 27 in digital output mode.
Pulse Output Actual value of pulses applied to
#29 [Hz] terminal 29 in digital output mode.
Relay Output View the setting of all relays.
[bin]
Counter A View the present value of counter A.
Counter B View the present value of counter B.
Prec. Stop
Counter
Analog In Actual value of the signal on input
X30/11 ®
X30/11 (VLT General Purpose I/O MCB
101, optional).
3 3
31