Danfoss VLT AQUA Drive FC 202 Instruction Manual
  1. Manuals
  2. Brands
  3. Danfoss Manuals
  4. DC Drives
  5. VLT AQUA Drive FC 202
  6. Instruction manual
Danfoss VLT AQUA Drive FC 202 Instruction Manual

Danfoss VLT AQUA Drive FC 202 Instruction Manual

0.25–90 kw
Hide thumbs Also See for VLT AQUA Drive FC 202:
Table of Contents

Advertisement

Quick Links

Download this manual See also: Programming Manual, Instruction Manual
MAKING MODERN LIVING POSSIBLE
Instruction Manual
®
VLT
AQUA Drive FC 202
0.25–90 kW
www.DanfossDrives.com

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the VLT AQUA Drive FC 202 and is the answer not in the manual?

Questions and answers

Related Manuals for Danfoss VLT AQUA Drive FC 202

Summary of Contents for Danfoss VLT AQUA Drive FC 202

  • Page 1 MAKING MODERN LIVING POSSIBLE Instruction Manual ® AQUA Drive FC 202 0.25–90 kW www.DanfossDrives.com...

  • Page 3: Table Of Contents

    4.8.3 Enabling Motor Operation (Terminal 27) 4.8.4 Voltage/Current Input Selection (Switches) 4.8.5 Safe Torque Off (STO) 4.8.6 RS-485 Serial Communication 4.9 Installation Check List 5 Commissioning 5.1 Safety Instructions 5.2 Applying Power 5.3 Local Control Panel Operation MG20MA22 Danfoss A/S © 10/2014 All rights reserved.
  • Page 4 8.6 Control Input/Output and Control Data 8.7 Connection Tightening Torques 8.8 Fuses and Circuit Breakers 8.9 Power Ratings, Weight and Dimensions 9 Appendix 9.1 Symbols, Abbreviations and Conventions 9.2 Parameter Menu Structure Danfoss A/S © 10/2014 All rights reserved. MG20MA22...
  • Page 5 Contents Instruction Manual Index MG20MA22 Danfoss A/S © 10/2014 All rights reserved.

  • Page 6: Introduction

    This manual is regularly reviewed and updated. All suggestions for improvement are welcome. Table 1.1 shows the document version and the corresponding software version. Edition Remarks Software version MG20MAxx Replaces MG20M9xx 2.xx Table 1.1 Document and Software Version Danfoss A/S © 10/2014 All rights reserved. MG20MA22...
  • Page 7 Check valve protection • Safe Torque Off • Low flow detection • Pipe fill mode • Sleep mode • Real time clock • Password protection • Overload protection • Smart logic control MG20MA22 Danfoss A/S © 10/2014 All rights reserved.
  • Page 8 Motor output terminals 96 (U), 97 (V), 98 (W) Analog switches (A53), (A54) Line power input terminals 91 (L1), 92 (L2), 93 (L3) Relay 1 (01, 02, 03) Figure 1.1 Exploded View Enclosure Types B and C, IP55 and IP66 Danfoss A/S © 10/2014 All rights reserved. MG20MA22...
  • Page 9 Decoupling plate Serial bus terminal switch Grounding clamp (PE) Digital I/O and 24 V power supply Shielded cable grounding clamp and strain relief Cover Figure 1.2 Exploded View Enclosure Type A, IP20 MG20MA22 Danfoss A/S © 10/2014 All rights reserved.

  • Page 10: Approvals And Certifications

    Table 1.3 Approvals and Certifications circuit voltage • Prove line transient protection More approvals and certifications are available. Contact local Danfoss partner. Adjustable frequency drives of • Reduce RMS current enclosure type T7 (525–690 V) are not certified for UL. DC reactors •...

  • Page 11: Safety

    Additionally, the personnel must be familiar readiness when the adjustable frequency drive with the instructions and safety measures described in this is connected to AC line power. document. MG20MA22 Danfoss A/S © 10/2014 All rights reserved.
  • Page 12 Leakage currents exceed 3.5 mA. Failure to ground the adjustable frequency drive properly could result in death or serious injury. • Ensure correct grounding of the equipment by a certified electrical installer. Danfoss A/S © 10/2014 All rights reserved. MG20MA22...

  • Page 13: Mechanical Installation

    Input voltage, frequency and current (at low/high voltages) Output voltage, frequency and current (at low/high voltages) Enclosure type and IP rating Maximum ambient temperature Certifications Discharge time (Warning) Figure 3.1 Product Nameplate (Example) MG20MA22 Danfoss A/S © 10/2014 All rights reserved.

  • Page 14: Mounting

    C2, C4 a (ins [mm]) 3.94 [100] 7.87 [200] 7.87 [200] 8.86 [225] Figure 3.3 Proper Mounting with Backplate Table 3.1 Minimum Airflow Clearance Requirements NOTICE! Backplate is required when mounted on railings. Danfoss A/S © 10/2014 All rights reserved. MG20MA22...
  • Page 15 Mechanical Installation Instruction Manual Figure 3.4 Top and Bottom Mounting Holes (See chapter 8.9 Power Ratings, Weight and Dimensions) Figure 3.5 Top and Bottom Mounting Holes (B4, C3, C4) MG20MA22 Danfoss A/S © 10/2014 All rights reserved.

  • Page 16: Electrical Installation

    • Minimum cable cross-section: AWG 7 [10 mm See maximum fuse ratings in chapter 8.8 Fuses (or two rated ground wires terminated and Circuit Breakers. separately). Danfoss A/S © 10/2014 All rights reserved. MG20MA22...
  • Page 17 Risk of electrical interference, when the ground potential between the adjustable frequency drive and the system is different. Install equalizing cables between the system components. Recommended cable cross-section: AWG 6 [16 mm MG20MA22 Danfoss A/S © 10/2014 All rights reserved.

  • Page 18: Wiring Schematic

    *Terminal 37 (optional) is used for Safe Torque Off. For Safe Torque Off installation instructions, refer to the Safe Torque Off ® Instruction Manual for Danfoss VLT Adjustable Frequency Drives. **Do not connect cable shield. Danfoss A/S © 10/2014 All rights reserved. MG20MA22...
  • Page 19 Run cables for input power, motor wiring and control wiring in three separate metallic conduits. Failure to isolate power, motor and control cables can result in unintended behavior or reduced performance. Minimum 7.9 in [200 mm] clearance between power, motor and control cables is required. MG20MA22 Danfoss A/S © 10/2014 All rights reserved.

  • Page 20: Access

    Figure 4.5. Connect the 3-phase motor wiring to terminals 96 (U), 97 (V), and 98 (W), see Figure 4.5. Tighten terminals in accordance with the information provided in chapter 8.7 Connection Tightening Torques. Danfoss A/S © 10/2014 All rights reserved. MG20MA22...

  • Page 21: Ac Line Input Connection

    A 24 V DC supply voltage is recommended. - LC - Figure 4.6 Example of Motor, Line Power and Ground Wiring MG20MA22 Danfoss A/S © 10/2014 All rights reserved.

  • Page 22: Control Terminal Types

    Connector 4 is a USB port available for use with the event of EMC the MCT 10 Set-up Software. problems. 68 (+) RS-485 Interface. A control card switch is provided for 69 (-) termination resistance. Relays Danfoss A/S © 10/2014 All rights reserved. MG20MA22...

  • Page 23: Wiring To Control Terminals

    Remove the screwdriver to fasten the control wire into the contact. Ensure the contact is firmly established and not loose. Loose control wiring can be the source of equipment faults or less than optimal operation. MG20MA22 Danfoss A/S © 10/2014 All rights reserved.

  • Page 24: Safe Torque Off (Sto)

    • Option cards which can be installed in the adjustable frequency drive are available to provide additional communication protocols. See the option-card documentation for installation and instruction manual. Danfoss A/S © 10/2014 All rights reserved. MG20MA22...

  • Page 25: Installation Check List

    POTENTIAL HAZARD IN THE EVENT OF INTERNAL FAILURE Risk of personal injury when the adjustable frequency drive is not properly closed. • Before applying power, ensure all safety covers are in place and securely fastened. MG20MA22 Danfoss A/S © 10/2014 All rights reserved.

  • Page 26: Commissioning

    REMOTE COASTING or Alarm 60 External Interlock is displayed, this indicates that the unit is ready to operate but is missing an input signal on terminal 27. See chapter 4.8.3 Enabling Motor Operation (Terminal 27) for details. Danfoss A/S © 10/2014 All rights reserved. MG20MA22...

  • Page 27: Local Control Panel Operation

    B. Display menu keys 0-21 Motor Current C. Navigation keys and indicator lights (LEDs) 0-22 Power [kW] 0-23 Frequency D. Operation keys and reset 0-24 Reference [%] Table 5.1 Legend to Figure 5.1, Display Area MG20MA22 Danfoss A/S © 10/2014 All rights reserved.
  • Page 28 Table 5.5 Legend to Figure 5.1, Operation Keys and Reset Table 5.3 Legend to Figure 5.1, Navigation Keys NOTICE! The display contrast can be adjusted by pressing [Status] ▲ ▼ and [ ] keys. Danfoss A/S © 10/2014 All rights reserved. MG20MA22...
  • Page 29 Press [Reset] to return to operation mode. Press [Quick Menu] or [Main Menu] on the LCP. ▲ ▼ Press [ ] to browse through the parameter groups, press [OK] to select a parameter group. MG20MA22 Danfoss A/S © 10/2014 All rights reserved.

  • Page 30: Basic Programming

    2 - ** Brakes NOTICE! 3 - ** Reference / Ramps Motor data are required for the SmartStart set-up. The Figure 5.2 Main Menu required data are normally available on the motor nameplate. Danfoss A/S © 10/2014 All rights reserved. MG20MA22...

  • Page 31: Asynchronous Motor Set-Up

    12 and 27. common (starpoint) value. 3-02 Minimum Reference. 3-03 Maximum Reference. 3-41 Ramp 1 Ramp-up Time. 3-42 Ramp 1 Ramp-down Time. 3-13 Reference Site. Linked to Hand/Auto Local Remote. MG20MA22 Danfoss A/S © 10/2014 All rights reserved.

  • Page 32: Automatic Energy Optimization (Aeo)

    • Reduced energy consumption • Reduced motor heating • Reduced motor noise To activate AEO, set parameter 1-03 Torque Characteristics to [2] Auto Energy Optim. CT or [3] Auto Energy Optim. VT. Danfoss A/S © 10/2014 All rights reserved. MG20MA22...

  • Page 33: Automatic Motor Adaptation (Ama)

    [OK]. drive side of the connection. Select [1] Enable complete AMA and press [OK]. Follow the on-screen instructions. The test runs automatically and indicate when it is complete. MG20MA22 Danfoss A/S © 10/2014 All rights reserved.

  • Page 34: Local Control Test

    Check sound and vibration level of the motor to after a trip. ensure that the system is working as intended. If warnings or alarms occur, see chapter 7.4 List of Warnings and Alarms. Danfoss A/S © 10/2014 All rights reserved. MG20MA22...

  • Page 35: Application Set-Up Examples

    D IN 37 is an option. A IN U - I A OUT 0 - 10V A 54 U - I Table 6.1 Analog Current Feedback Transducer Table 6.3 Analog Voltage Feedback Transducer (4-wire) MG20MA22 Danfoss A/S © 10/2014 All rights reserved.
  • Page 36 A IN D IN 37 is an option. A IN A OUT 4 - 20mA A OUT U - I Table 6.7 Run/Stop Command with External Interlock Table 6.5 Analog Speed Reference (Current) Danfoss A/S © 10/2014 All rights reserved. MG20MA22...
  • Page 37 Notes/comments: D IN D IN 37 is an option. D IN D IN D IN D IN D IN +10 V A IN A IN A OUT Table 6.10 External Alarm Reset MG20MA22 Danfoss A/S © 10/2014 All rights reserved.
  • Page 38 [1] Thermistor +10 V warning. A IN D IN 37 is an option. A IN RS-485 A OUT U - I Table 6.11 RS-485 Network Connection Table 6.12 Motor Thermistor Danfoss A/S © 10/2014 All rights reserved. MG20MA22...

  • Page 39: Maintenance, Diagnostics And Troubleshooting

    The adjustable frequency drive is controlled by the navigation keys on the LCP. Stop commands, reset, reversing, DC brake, and other signals applied to the control terminals override local control. Table 7.1 Operation Mode MG20MA22 Danfoss A/S © 10/2014 All rights reserved.
  • Page 40 29) is active. • The Jog function is activated via the serial communication. • The Jog function was selected as a reaction for a monitoring function (e.g., No signal). The monitoring function is active. Danfoss A/S © 10/2014 All rights reserved. MG20MA22...
  • Page 41 Run request A start command was given, but the motor remains stopped until a run permissive signal is received via digital input. Running The motor is driven by the adjustable frequency drive. MG20MA22 Danfoss A/S © 10/2014 All rights reserved.

  • Page 42: Warning And Alarm Types

    Warning LED Alarm LED fault, and reset the adjustable frequency drive. Warning Alarm On (Flashing) Trip Lock On (Flashing) Table 7.4 Status Indicator Lights Explanations Danfoss A/S © 10/2014 All rights reserved. MG20MA22...

  • Page 43: List Of Warnings And Alarms

    The intermediate circuit voltage (DC) is higher than the continuous current rating, the counter should high voltage warning limit. The limit is dependent on the decrease adjustable frequency drive voltage rating. The unit is still active. MG20MA22 Danfoss A/S © 10/2014 All rights reserved.
  • Page 44 1-95 KTY Sensor Type, 1-96 KTY Thermistor board hardware or software. Resource, and 1-97 KTY Threshold level match sensor wiring Record the value of the following parameters and contact the Danfoss supplier: Danfoss A/S © 10/2014 All rights reserved. MG20MA22...
  • Page 45 14-53 Fan Monitor ([0] Disabled). brake resistors Klixon inputs, see Brake Resistor Temperature Troubleshooting Switch in the Design Guide. • Check fan resistance • Check soft charge fuses MG20MA22 Danfoss A/S © 10/2014 All rights reserved.
  • Page 46 Check for loose or missing wiring • Dirty heatsink Contact the Danfoss supplier or service department if This alarm is based on the temperature measured by the required. Note the code number for further trouble- heatsink sensor mounted inside the IGBT modules.
  • Page 47 No communication from ATACD to DSP (state running). 2816 Stack overflow control board module. 2817 Scheduler slow tasks. 2818 Fast tasks. 2819 Parameter thread. 2820 LCP stack overflow. 2821 Serial port overflow. 2822 USB port overflow. MG20MA22 Danfoss A/S © 10/2014 All rights reserved.
  • Page 48 DC link voltage. ALARM 50, AMA calibration failed WARNING/ALARM 65, Control card over temperature Contact the Danfoss supplier or Danfoss Service The control card has reached its trip temperature of 167 °F Department. [75 °C].
  • Page 49 The fan monitor checks that the fan is spinning at number. adjustable frequency drive power-up or whenever the mixing fan is turned on. If the fan is not operating, then the fault is annunciated. The mixing-fan fault can be MG20MA22 Danfoss A/S © 10/2014 All rights reserved.
  • Page 50 Reset the adjustable frequency drive for normal operation. WARNING 251, New type code The power card or other components have been replaced and the type code changed. Reset to remove the warning and resume normal operation. Danfoss A/S © 10/2014 All rights reserved. MG20MA22...

  • Page 51: Troubleshooting

    Check if a reversing command is Deactivate reversing signal. in wrong programmed for the terminal in parameter direction group 5-1* Digital inputs. Wrong motor phase connection See chapter 5.5 Checking Motor Rotation. MG20MA22 Danfoss A/S © 10/2014 All rights reserved.
  • Page 52 If warnings or alarms occur, see frequency incorrectly chapter 7.4 List of Warnings and Alarms. 1 Ramp-down Time. Enable overvoltage drive Check that motor data are entered control in 2-17 Over-voltage Control. deceleration correctly. problems Danfoss A/S © 10/2014 All rights reserved. MG20MA22...
  • Page 53 Turn off over-modulation in 14-03 Overmo- Acoustic noise dulation. or vibration Change switching pattern and frequency in parameter group 14-0* Inverter Switching. Increase Resonance Dampening in 1-64 Resonance Damping. Table 7.6 Troubleshooting MG20MA22 Danfoss A/S © 10/2014 All rights reserved.

  • Page 54: Specifications

    Estimated power loss at rated maximum load [W] 0.98 0.98 0.98 0.98 0.98 0.98 0.98 0.98 0.98 Efficiency Table 8.1 Mains Supply 1x200–240 V AC, Normal Overload 110% for 1 Minute, P1K1–P22K Danfoss A/S © 10/2014 All rights reserved. MG20MA22...

  • Page 55: Line Power Supply 3X200-240 V Ac

    Max. cable size (line power, motor, brake) [mm [0.2–4]/(4–10) (AWG)] 0.94 0.94 0.95 0.95 0.96 0.96 0.96 0.96 0.96 Efficiency Table 8.2 Line Power Supply 3x200–240 V AC - Normal overload 110% for 1 minute, PK25-P3K7 MG20MA22 Danfoss A/S © 10/2014 All rights reserved.

  • Page 56: Line Power Supply 1X380-480 V Ac

    Max. cable size (line power, motor, brake) [mm ]/(AWG) [10]/(7) [35]/(2) [50]/(1/0) [120]/(4/0) 0.96 0.96 0.96 0.96 Efficiency Table 8.4 Line Power Supply 1x380–480 V AC - Normal Overload 110% for 1 Minute, P7K5-P37K Danfoss A/S © 10/2014 All rights reserved. MG20MA22...

  • Page 57: Line Power Supply 3X380-480 V Ac

    Max. cable size (line power, motor, [4]/(10) brake) [mm ]/(AWG) Efficiency 0.93 0.95 0.96 0.96 0.97 0.97 0.97 0.97 0.97 0.97 Table 8.5 Line Power Supply 3x380–480 V AC - Normal overload 110% for 1 minute, PK37-P7K5 MG20MA22 Danfoss A/S © 10/2014 All rights reserved.
  • Page 58 [mm ]/(AWG) (4/0) (4/0) 0.98 0.98 0.98 0.98 0.98 0.98 0.98 0.98 0.98 0.99 Efficiency Table 8.6 Line Power Supply 3x380–480 V AC - Normal overload 110% for 1 minute, P11K-P90K Danfoss A/S © 10/2014 All rights reserved. MG20MA22...

  • Page 59: Line Power Supply 3X525-600 V Ac

    Max. cable size (line power, motor, [0.2–4]/(24–10) [16]/(6) brake) [mm ]/(AWG) Efficiency 0.97 0.97 0.97 0.97 0.97 0.97 0.97 0.97 0.98 Table 8.7 Line Power Supply 3x525–600 V AC - Normal overload 110% for 1 minute, PK75-P11K MG20MA22 Danfoss A/S © 10/2014 All rights reserved.

  • Page 60: Line Power Supply 3 X 525-690 V Ac

    6, 4, 4 (10, 12, 12) ] ([AWG]) Estimated power loss at rated max. load (W) Efficiency 0.96 0.96 0.96 0.96 0.96 0.96 0.96 Table 8.9 A3 Enclosure, Line Power Supply 3x525–690 V AC IP20/Protected Chassis, P1K1-P7K5 Danfoss A/S © 10/2014 All rights reserved. MG20MA22...
  • Page 61 [mm ] ([AWG]) Estimated power loss at rated max. load (W) Efficiency 0.98 0.98 0.98 0.98 Table 8.10 B2/B4 Enclosure, Line Power Supply 3x525–690 V AC IP20/IP21/IP55 - Chassis/NEMA 1/NEMA 12, P11K-P22K MG20MA22 Danfoss A/S © 10/2014 All rights reserved.
  • Page 62 7) Enclosure sizes B3+B4 and C3+C4 can be converted to IP21 using a conversion kit. See also Mechanical mounting and IP21/Type 1 Enclosure kit in the Design Guide. 8) Enclosure sizes for N75K, N90K are D3h for IP20/Chassis, and D5h for IP54/Type 12. 9) 2 wires are required. 10) Variant not available in IP21. Danfoss A/S © 10/2014 All rights reserved. MG20MA22...

  • Page 63: Line Power Supply

    Maximum 110% for 1 min. Starting torque maximum 135% up to 0.5 s Overload torque (Constant torque) Maximum 110% for 1 min. *Percentage relates to the nominal torque of the adjustable frequency drive. MG20MA22 Danfoss A/S © 10/2014 All rights reserved.

  • Page 64: Ambient Conditions

    Minimum cross-section to control terminals 0.00039 in [0.25 mm For power cables, see electrical data tables in chapter 8.1 Electrical Data. * See electrical data tables in chapter 8.1 Electrical Data for more information! Danfoss A/S © 10/2014 All rights reserved. MG20MA22...

  • Page 65: Control Input/Output And Control Data

    Max. resistor load to common at analog output Accuracy on analog output Max. error: 0.8% of full scale Resolution on analog output 8 bit The analog output is galvanically isolated from the supply voltage (PELV) and other high-voltage terminals. MG20MA22 Danfoss A/S © 10/2014 All rights reserved.
  • Page 66 12, 13 Max. load 200 mA The 24 V DC supply is galvanically isolated from the supply voltage (PELV), but has the same potential as the analog and digital inputs and outputs. Danfoss A/S © 10/2014 All rights reserved. MG20MA22...
  • Page 67 The USB connection is galvanically isolated from the supply voltage (PELV) and other high-voltage terminals. The USB connection is not galvanically isolated from ground protection. Use only isolated laptop/PC as connection to the USB connector on the adjustable frequency drive or an isolated USB cable/drive. MG20MA22 Danfoss A/S © 10/2014 All rights reserved.

  • Page 68: Connection Tightening Torques

    The fuses below are suitable for use on a circuit capable of delivering 100,000 Arms (symmetrical), depending on the adjustable frequency drive voltage rating. With the proper fusing the adjustable frequency drive Short Circuit Current Rating (SCCR) is 100,000 Arms. Danfoss A/S © 10/2014 All rights reserved. MG20MA22...
  • Page 69 NZMB2-A200 aR-125 (30 [22]) aR-160 (30 [22]) 50–60 [37–45] aR-160 (40 [30]) aR-200 (40 [30]) NZMB2-A250 aR-200 (50 [37]) aR-250 (50 [37]) Table 8.13 200–240 V, Enclosure Types A, B and C MG20MA22 Danfoss A/S © 10/2014 All rights reserved.
  • Page 70 (50 [37]) gG-150 (50 [37]) NZMB2-A200 gG-160 (60 [45]) gG-160 (60 [45]) 100–125 [75–90] aR-200 (75 [55]) aR-250 NZMB2-A250 aR-250 (100 [75]) Table 8.14 380–480 V, Enclosure Types A, B and C Danfoss A/S © 10/2014 All rights reserved. MG20MA22...
  • Page 71 NZMB2-A250 60–75 [45–55] gG-63 (50 [37]) gG-150 NZMB2-A200 gG-100 (60 [45]) 100–125 [75–90] aR-160 (75 [55]) aR-250 NZMB2-A250 aR-200 (100 [75]) Table 8.15 525–600 V, Enclosure Types A, B and C MG20MA22 Danfoss A/S © 10/2014 All rights reserved.
  • Page 72 50 [37] gG-63 gG-80 60 [45] gG-63 gG-100 75 [55] gG-80 gG-125 100 [75] gG-100 gG-160 50 [37] gG-100 gG-125 60 [45] gG-125 gG-160 Table 8.16 525–690 V, Enclosure Types A, B, C Danfoss A/S © 10/2014 All rights reserved. MG20MA22...
  • Page 73 Table 8.18 1x380–500 V, Enclosure Types B and C KTS fuses from Bussmann may substitute KTN for 240 V adjustable frequency drives. FWH fuses from Bussmann may substitute FWX for 240 V adjustable frequency drives. MG20MA22 Danfoss A/S © 10/2014 All rights reserved.
  • Page 74 1) KTS fuses from Bussmann may substitute KTN for 240 V adjustable frequency drives. 2) FWH fuses from Bussmann may substitute FWX for 240 V adjustable frequency drives. 3) A6KR fuses from Ferraz-Shawmut may substitute A2KR for 240 V adjustable frequency drives. Danfoss A/S © 10/2014 All rights reserved. MG20MA22...
  • Page 75 A6K-200-R FWH-200 HSJ-200 A50-P-225 L50-S-225 125 [90] 2028220-250 KLS-R-250 A6K-250-R FWH-250 HSJ-250 A50-P-250 L50-S-250 Table 8.22 3x380–480 V, Enclosure Types A, B and C 1) Ferraz-Shawmut A50QS fuses may substitute A50P fuses. MG20MA22 Danfoss A/S © 10/2014 All rights reserved.
  • Page 76 Table 8.23 3x525–600 V, Enclosure Types A, B and C 1) 170M fuses shown from Bussmann use the -/80 visual indicator. –TN/80 Type T, -/110 or TN/110 Type T indicator fuses of the same size and amperage may be substituted. Danfoss A/S © 10/2014 All rights reserved. MG20MA22...
  • Page 77 JJS-100 5014006-100 KLS-R-100 A6K-100-R HST-100 100 [75] KTS-R-125 JKS-125 JJS-125 2028220-125 KLS-150 A6K-125-R HST-125 125 [90] KTS-R-150 JKS-150 JJS-150 2028220-150 KLS-175 A6K-150-R HST-150 Table 8.24 3x525–690 V, Enclosure Types B and C MG20MA22 Danfoss A/S © 10/2014 All rights reserved.

  • Page 78: Power Ratings, Weight And Dimensions

    Specifications ® AQUA Drive FC 202 8.9 Power Ratings, Weight and Dimensions Danfoss A/S © 10/2014 All rights reserved. MG20MA22...
  • Page 79 Specifications Instruction Manual MG20MA22 Danfoss A/S © 10/2014 All rights reserved.

  • Page 80: Appendix

    Table 9.1 Symbols and Abbreviations Conventions Numbered lists indicate procedures. Bullet lists indicate other information and description of figures. Italicized text indicates • cross reference • link • parameter name 9.2 Parameter Menu Structure Danfoss A/S © 10/2014 All rights reserved. MG20MA22...
  • Page 81 Appendix Instruction Manual MG20MA22 Danfoss A/S © 10/2014 All rights reserved.
  • Page 82 Appendix ® AQUA Drive FC 202 Danfoss A/S © 10/2014 All rights reserved. MG20MA22...
  • Page 83 Appendix Instruction Manual MG20MA22 Danfoss A/S © 10/2014 All rights reserved.
  • Page 84 Appendix ® AQUA Drive FC 202 Danfoss A/S © 10/2014 All rights reserved. MG20MA22...
  • Page 85 Control Card performance..............65 Fuses................14, 23, 44, 49, 66 Control card, 10 V DC output............65 Control Card, 24 V DC output............64 Control card, RS-485 serial communication....... 63 Ground connections................23 MG20MA22 Danfoss A/S © 10/2014 All rights reserved.
  • Page 86 Manual initialization................28 Power connection................14 MCT 10....................20, 25 Power factor..................8, 23 Menu keys....................25 Programming............. 21, 25, 26, 27, 41 Menu Keys....................26 Pulse Inputs.................... 64 Menu structure..................26 Danfoss A/S © 10/2014 All rights reserved. MG20MA22...
  • Page 87 Sleep Mode..................... 39 Specifications..................22 Speed reference............... 21, 32, 34, 38 Start-up....................27 Status mode................... 37 Storage..................... 11 Supply voltage..............19, 20, 24, 44 Switch....................... 21 Switching frequency................39 Symbols....................78 System feedback..................4 MG20MA22 Danfoss A/S © 10/2014 All rights reserved.
  • Page 88 Danfoss shall not be responsible for any errors in catalogs, brochures or other printed material. Danfoss reserves the right to alter its products at any time without notice, provided that alterations to products already on order shall not require material changes in specifications previously agreed upon by Danfoss and the Purchaser. All trademarks in this material are property of the respective companies.

Table of Contents