Danfoss VLT AQUA Drive FC 202 Programming Manual page 234

Parameter Description
3.24.11 27-7* Connections
Parameters for configuring relay connections.
27-70 Relay
This parameter is only relevant for a relay wiring configuration.
3 3
Use this parameter to set up the function of the option relays.
This parameter is an array. The visibility of options depends on
the MCO option installed in the frequency converter:
•
®
VLT
12 are available.
•
®
VLT
13-20 are available.
In any case, the standard relays (Relay 1 and Relay 2), and the
relays in the VLT
To set the function of a specific relay, select the relay and then
select the function. If the option [0] Standard Relay is selected,
the relay can be used as a general-purpose relay and the
function can be set in parameter group 5-4* Relays.
Option:
[0] Standard Relay
*
[1] Drive 2 Enable
[2] Drive 3 Enable
[3] Drive 4 Enable
[4] Drive 5 Enable
[5] Drive 6 Enable
[6] Drive 7 Enable
[7] Drive 8 Enable
[8] Pump 1 to Drive 1
[9] Pump 1 to Drive 2
[10] Pump 1 to Drive 3
[11] Pump 1 to Drive 4
[12] Pump 1 to Drive 5
[13] Pump 1 to Drive 6
[14] Pump 1 to Drive 7
[15] Pump 1 to Drive 8
[16] Pump 2 to Drive 1
[17] Pump 2 to Drive 2
[18] Pump 2 to Drive 3
[19] Pump 2 to Drive 4
[20] Pump 2 to Drive 5
[21] Pump 2 to Drive 6
[22] Pump 2 to Drive 7
[23] Pump 2 to Drive 8
[24] Pump 3 to Drive 1
[25] Pump 3 to Drive 2
[26] Pump 3 to Drive 3
[27] Pump 3 to Drive 4
[28] Pump 3 to Drive 5
[29] Pump 3 to Drive 6
[30] Pump 3 to Drive 7
[31] Pump 3 to Drive 8
232
Extended Cascade Controller MCO 101: Relays 10–
Advanced Cascade Controller MCO 102: Relays
®
Relay Option MCB 105 are available.
Danfoss A/S © 05/2018 All rights reserved.
®
VLT AQUA Drive FC 202
27-70 Relay
This parameter is only relevant for a relay wiring configuration.
Use this parameter to set up the function of the option relays.
This parameter is an array. The visibility of options depends on
the MCO option installed in the frequency converter:
•
•
In any case, the standard relays (Relay 1 and Relay 2), and the
relays in the VLT
To set the function of a specific relay, select the relay and then
select the function. If the option [0] Standard Relay is selected,
the relay can be used as a general-purpose relay and the
function can be set in parameter group 5-4* Relays.
Option:
[32]
[33]
[34]
Function:
[35]
Enable slave
[36]
frequency
[37]
converter X.
[38]
[39]
[40]
[41]
[42]
[43]
[44]
[45]
[46]
[47]
[48]
[49]
[50]
[51]
[52]
[53]
[54]
[55]
[56]
[57]
[58]
[59]
[60]
[61]
[62]
[63]
[64]
[65]
[66]
[67]
[68]
[69]
®
VLT Extended Cascade Controller MCO 101: Relays 10–
12 are available.
®
VLT Advanced Cascade Controller MCO 102: Relays
13-20 are available.
®
Relay Option MCB 105 are available.
Pump 4 to Drive 1
Pump 4 to Drive 2
Pump 4 to Drive 3
Pump 4 to Drive 4
Pump 4 to Drive 5
Pump 4 to Drive 6
Pump 4 to Drive 7
Pump 4 to Drive 8
Pump 5 to Drive 1
Pump 5 to Drive 2
Pump 5 to Drive 3
Pump 5 to Drive 4
Pump 5 to Drive 5
Pump 5 to Drive 6
Pump 5 to Drive 7
Pump 5 to Drive 8
Pump 6 to Drive 1
Pump 6 to Drive 2
Pump 6 to Drive 3
Pump 6 to Drive 4
Pump 6 to Drive 5
Pump 6 to Drive 6
Pump 6 to Drive 7
Pump 6 to Drive 8
Pump 7 to Drive 1
Pump 7 to Drive 2
Pump 7 to Drive 3
Pump 7 to Drive 4
Pump 7 to Drive 5
Pump 7 to Drive 6
Pump 7 to Drive 7
Pump 7 to Drive 8
Pump 8 to Drive 1
Pump 8 to Drive 2
Pump 8 to Drive 3
Pump 8 to Drive 4
Pump 8 to Drive 5
Pump 8 to Drive 6
Function:
MG20OB02