Table of Contents
Advertisement
APPENDIX F REVISION HISTORY
Appendix F: Revision History
Rev. No.
Date
0.8
2007.9.21
0.9
2007.10.28
2-3 to 2-5 2.3 Command Set
Page
Section
1-3
1.3.1 Pinout Diagram
1-4
1.3.2 Pin Descriptions
23-1
23 Basic External Connection Diagram
AP-31
Appendix D: Initialization Routine
1-2
1-2 Block Diagram
2-1
2.1 S1C17 Core Features
2-7
2.4 Vector Table
3-1
3 Memory Map and Bus Control
3-2
3.1 Bus Cycle
3-2
3.1.2 Command Execution Cycle Restrictions
3-3
3.2 Internal ROM Area
3-4
3.3 Internal RAM Area
3-5
3.4 Internal Peripheral Circuit Area
5-3
5.2 Initial Reset Sequence
6-1
6.1 ITC Configuration
6-2
6.2 Vector Table
6-3
6.3.2 Interrupt Request from Peripheral
Module and Interrupt Flag
6-8
6.3.6 S1C17 Core Interrupt Processing
6-11
6.6 HALT and SLEEP Mode Cancellation by
Interrupt Factors
6-13
6.7 Control Register Details
6-15
7-1
7.1 OSC Module Configuration
8-1
8.1 Clock Generator Configuration
10-1
10.1 Input/Output Port Configuration
10-2
10.2 Input/Output Port Pin Function Selec-
tion (Port MUX)
10-3
10.3 Data Input/Output
10-4
10.4 Pull-up Control
10-7
10.7 Port Input Interrupt
10-24
10.9 Precautions
11-3
11.2.2 External Clock Mode
11-8
11.6 16-bit Timer RUN/STOP Control
11-10
11.8 16-bit Timer Interrupts
12-2
12.2 8-bit Timer Count Mode
12-6
12.6 8-bit Timer RUN/STOP Control
12-9
12.9 8-bit Timer Interrupts
12-15
12.10 Control Register Details
13-4
13.4 Compare Data Settings
13-5
13.5 PWM & Capture Timer RUN/STOP
Control
Details
Figure 1.3.1.1 changed
Table 1.3.2.1 changed
Figure changed and added
Sample program changed
Figure 1.2.1 changed
Description changed
"It features low power consumption, ... are widely used."
Table 2.3.1 changed
Note (*2) added
Table 2.4.1 changed
Figure 3.1 changed
Description changed
"Interrupt processing stack operation involves reading
... in the last 24 bits."
Section changed
Section title changed
Section title changed
Description changed
"The 1 Kbyte area starting at address 0x4000 ... and
control registers."
Description changed
"CPU startup waits for ... OSC3 clock frequency"
Figure 6.1.1 changed
Table 6.2.1 changed
Table 6.3.2.1 changed
Description added
"- ITEN ... has been set to 1."
Section title changed
Description changed
"HALT and SLEEP modes are ... in Appendix B."
Table 6.7.2 changed
Table 6.7.4 changed
Figure 7.1.1 changed
Figure 8.1.1 changed
Description (note) changed
"Switch on the ... using this function."
Description changed
"Resetting the ... in Table 10.2.1)."
Description changed
"The input/output ports ... PxIO[7:0] (Px_IO register)."
Description changed
"The input/output port contains a pull-up resistor, ...
(Px_PU register)."
Description changed
"The interrupt controller ... Interrupt Controller (ITC)."
Description added
Pull-up
"- Input/output ports that are not used ... enabled."
Description changed
"For instructions on controlling chattering filter circuits,
... Function."
Description changed (one location only)
ITC → interrupt controller (ITC)
Description changed (one location only)
ITC → interrupt controller (ITC)
Description added
"Note: Make sure ... count mode settings."
Description changed (one location only)
ITC → interrupt controller (ITC)
Description changed (one location only)
ITC → interrupt controller (ITC)
Description added (0x4206, D4)
"Note: Make sure ... count mode settings."
Counter reset cycle calculation equation added
Description changed (one location only)
ITC → interrupt controller (ITC)
Advertisement
Table of Contents
