Table of Contents
Advertisement
Rev. No.
Date
0.9
2007.10.28
13-20
14-10
20-1, 20-11,
20-18 to
20-11
21-13
21-14
23-1 to 23-2 23 Basic External Connection Diagram
24-2 to 24-3 24.5 AC Characteristics
24-6 to 24-7
AP-23
AP-25
AP-26
AP-27
1.0
2008.1.30
Page
Section
13-8
13.6 Clock Output Control
13-9
13.7 PWM & Capture Timer Interrupts
13.9 Precautions
14-2
14.2 8-bit OSC1 Timer Count Mode
14-5
14.5 Compare Data Settings
14-6
14.6 8-bit OSC1 Timer RUN/STOP Control
14-7
14.7 8-bit OSC1 Timer Interrupts
14.8 Control Register Details
15-4
15.4 Clock Timer RUN/STOP Control
15-5
15.5 Clock Timer Interrupts
16-5
16.5 Stopwatch Timer RUN/STOP Control
16-6
16.6 Stopwatch Timer Interrupts
18-9
18.7 UART Interrupts
19-8
19.6 SPI Interrupts
2
20 I
C
20-19
2
20.6 I
C Interrupts
21-3
21.3 Carrier Generation
21-6
21.5 Data Transfer Control
21-8
21.6 REMC Interrupts
21.7 Control Register Details
22-1
22.1 Resource Requirements and Debug-
ging Tool
22-2
22.2 Debug Break Operation Status
22-4
22.3 Control Register Details
24-1
24.2 Recommended Operating Conditions
Appendix A: I/O Register List
B.1 Clock Control Power Saving
1-1
1.1 Features
7-2
7.2 OSC3 Oscillator Circuit
7.3
7.3 OSC1 Oscillator Circuit
11-3
11.2.2 External Clock Mode
APPENDIX F REVISION HISTORY
Details
Description changed
"If the counter data register ... A bit 0 (T16ECA0) value."
------
"Precautions
(1) Compare data ... (High when INVOUT = 1)."
Description changed (one location only)
ITC → interrupt controller (ITC)
Description changed
"- Setting compare data with A > B ... (High when
INVOUT = 1)."
Description added
"Note: Make sure... count mode settings."
Compare match cycle calculation equation added
Description changed (one location only)
ITC → interrupt controller (ITC)
Description changed (one location only)
ITC → interrupt controller (ITC)
Description added (0x50c0, D1)
"Note: Set the count mode ... stopped."
Description changed (one location only)
ITC → interrupt controller (ITC)
Description changed (one location only)
ITC → interrupt controller (ITC)
Description changed (one location only)
ITC → interrupt controller (ITC)
Description changed (one location only)
ITC → interrupt controller (ITC)
Description changed (one location only)
ITC → interrupt controller (ITC)
Description changed (one location only)
ITC → interrupt controller (ITC)
Interrupt name changed
Receive interrupt à Receive buffer full interrupt
Transmit interrupt à Transmit buffer empty interrupt
Description changed (one location only)
ITC → interrupt controller (ITC)
Carrier H/L section length calculation equation added
Description changed (one location only)
ITC → interrupt controller (ITC)
Description changed (one location only)
ITC → interrupt controller (ITC)
Carrier H section length calculation equation added
Carrier L section length calculation equation added
ICD name changed
ICD Mini → ICD (S5U1C17001H etc.)
Description added
"The 8-bit OSC1 timer... even if O1DBG is set to 1."
Description added
"The 8-bit OSC1 timer ... even if O1DBG is set to 1."
Table changed
Table changed
Sections 24.5.1 to 24.5.4 and tables added
Graph (TBD) added
Error corrected
0x5340-0x5347 Remote Controller
Figure B.1.1 changed
Description changed
"- Execute slp command
... to startup using ports (described later)."
Table B.1.1 and description changed
"Canceling HALT and SLEEP modes ... processing
routine."
TBD section fixed
Figure 7.2.1 changed
Description added
"A drain resistor (R
) should ... if required."
d
Figure 7.3.1 changed
Description added
"A drain resistor (R
) should ... if required."
d
(TBD) deleted
Advertisement
Table of Contents
