Prog_Sd_Reset_Save_Tab; Nc_User_Code_Conf_Name_Tab - Siemens SINUMERIK 808D Parameter Manual

SD43790 $SA_OSCILL_START_POS
10710

PROG_SD_RESET_SAVE_TAB

- Setting data to be updated
-
- 30
Description:
Setting data to be backed up
The values of the SDs listed in this table are stored in non-volatile memory, i.e. they
remain valid after power ON. The setting data whose HMI numbers were entered in the
backup list are written into the (buffered) active file system after the description
of the part program on reset.
Programmable setting data are:
SD 42000
SD 42010:
SD 42400
SD 42800
SD 43200:
SD 43202:
SD 43210
SD 43220
SD 43230
SD 43300
SD 43420
SD 43430
SD 43700
SD 43710
SD 43720
SD 43730
SD 43740
SD 43750
SD 43760
SD 43770
SD 43780
The values of D43420 $SA_WORKAREA_LIMIT_PLUS (working area limitation plus) and
SD43430 $SA_WORKAREA_LIMIT_MINUS (working area limitation minus) are to be stored in
the buffered RAM after every RESET, M02, M30 or M17.
-->
-->
See also: 'REDEF: change attributes of NC language elements', setting data/PRLOC
10712

NC_USER_CODE_CONF_NAME_TAB

- List of reconfigured NC codes
-
- 22
Description:
List of identifiers of the NC codes reconfigured by the user.
The list is to be structured as follows:
Even address:
Parameter Manual
List Manual, 01/2017
0, 0, 0, 0, 0, 0, 0, 0...
$SC_THREAD_START_ANGLE
$SC_THREAD_RAMP_DISP
$SC_PUNCH_DWELLTIME
$SC_SPIND_ASSIGN_TAB
$SA_SPIND_S
$SA_SPIND_CONSTCUT_S
$SA_SPIND_MIN_VELO_G25
$SA_SPIND_MAX_VELO_G26
$SA_SPIND_MAX_VELO_LIMS
$SA_ASSIGN_FEED_PER_REV_SOURCE
$SA_WORKAREA_LIMIT_PLUS
$SA_WORKAREA_LIMIT_MINUS
$SA_OSCILL_REVERSE_POS1
$SA_OSCILL_REVERSE_POS2
$SA_OSCILL_DWELL_TIME1
$SA_OSCILL_DWELL_TIME2
$SA_OSCILL_VELO
$SA_OSCILL_NUM_SPARK_CYCLES
$SA_OSCILL_END_POS
$SA_OSCILL_CTRL_MASK
$SA_OSCILL_IS_ACTIVE
PROG_SD_RESET_SAVE_TAB[0] = 43420
PROG_SD_RESET_SAVE_TAB[1] = 43430
G58, G59, G505, G58,
G506, G59, WAITM,
WAITM
EXP, N01
DWORD
- -
(GCODE)
EXP, N01, N12
STRING
- -
Identifier to be changed
3.2 General machine data
A3, V1
PowerOn
2/2
SF
DITS/DITE
PDELAYON
SETMS
S with G94,G95,G97,G971,G972
S with G96,G961,G962
G25S
G26 S
LIMS
FPRAON
G26
G25
OSP1
OSP2
OST1
OST2
FA
OSNSC
OSE
OSCTRL
OS
TE1, B1
PowerOn
2/2
Machine data
M
M
45