Siemens SINUMERIK 808D Parameter Manual page 244

Machine data
3.4 Axis-specific machine data
Description:
If a positioning axis is programmed in the part program without specifying the axis-
specific feedrate, the feedrate entered in MD32060 $MA_POS_AX_VELO is automatically
used for this axis. The feedrate in MD32060 $MA_POS_AX_VELO applies until an axis-
specific feedrate is programmed in the part program for this positioning axis.
MD irrelevant for:
MD32060 $MA_POS_AX_VELO is irrelevant for all axis types other than positioning axis.
Special cases:
If a
not traverse if it is programmed without feed. If a velocity is entered in MD32060
$MA_POS_AX_VELO that is higher than the maximum velocity of the axis (MD32000
$MA_MAX_AX_VELO), the velocity is automatically restricted to the maximum rate.
32080 HANDWH_MAX_INCR_SIZE
mm, degrees Limitation of selected increment
CTEQ
- -
Description:
> 0:
VDI signal>Ü or SD41010 $SN_JOG_VAR_INCR_SIZE for the associated machine axis
0:
32082 HANDWH_MAX_INCR_VELO_SIZE
mm/min, rev/min Limitation for velocity override
CTEQ
808d-me42 -
808d-me62 -
808d-te42 -
808d-te62 -
808d-mte40 -
808d-mte60 -
Description:
For the velocity override of positioning axes:
>0:
signal> 0 or SD41010 $SN_JOG_VAR_INCR_SIZE for the associated machine axis
0:
32084 HANDWH_STOP_COND
- Handwheel travel behavior
CTEQ
- -
Description:
Definition of the response of the handwheel travel to axis-specific VDI interface
signals or the CP-SW limit stop or a stop from an OEM application:
Bit = 0:
Interruption or collection of the distances preset via the handwheel.
Bit = 1:
244
ZERO velocity is entered in MD32060 $MA_POS_AX_VELO, the positioning axis does
0.0
Limitation of size of selected increment MD11330 $MN_JOG_INCR_SIZE <Increment/
No limitation
500., 500., 500., 1800.
500., 500., 500., 1800.,
1800.
500., 500., 500., 1800.
500., 500., 500., 1800.,
1800., 1800.
(500.0/1.0),
(500.0/1.0),
(500.0/1.0),
(500.0/1.0),
(500.0/1.0),...
(500.0/1.0),
(500.0/1.0),
(500.0/1.0),
(500.0/1.0),
(500.0/1.0),...
Limitation of size of selected increment $MN_JOG_INCR_SIZEL<Increment/VDI
No limitation
0x10FF
A05, A10
DOUBLE
0.0 -
A05, A10, A04
DOUBLE
(0./ 0.) (1.e300/ 1.e300)
(0./ 0.) (1.e300/ 1.e300)
(0./ 0.) (1.e300/ 1.e300)
(0./ 0.) (1.e300/ 1.e300)
(0./ 0.) (1.e300/ 1.e300)
(0./ 0.) (1.e300/ 1.e300)
EXP, A10
DWORD
0 0x17FF
H1
Reset
1/1 M
-
Reset
1/1 M
1/1 M
1/1 M
1/1 M
1/1 M
1/1 M
H1
Reset
1/1 M
Parameter Manual
List Manual, 01/2017