Siemens SINUMERIK 808D Parameter Manual page 242

Machine data
3.4 Axis-specific machine data
808d-mte40 -
808d-mte60 -
Description:
The velocity entered applies to traversing in JOG mode when the axial feedrate
override switch position is 100%.
This velocity is only used when general SD41110 $SN_JOG_SET_VELO = 0
and linear feedrate is selected (SD41100 $SN_JOG_REV_IS_ACTIVE = 0) or SD41130
$SN_JOG_ROT_AX_SET_VELO = 0 for rotary axes.
If this is the case, the axis velocity is active for
●
continuous jogging
●
incremental jogging (INC1, ... INCvar)
●
handwheel jogging
The value entered must not exceed the maximum permissible axis velocity (MD32000
$MA_MAX_AX_VELO).
If DRF is active, the axis velocity for JOG must be reduced with MD32090
$MA_HANDWH_VELO_OVERLAY_FACTOR.
Spindles in JOG mode:
This machine data can also be used to define the JOG mode speed for specific spindles
(if SD41200 $SN_JOG_SPIND_SET_VELO = 0). However, the speed can be modified with the
spindle override switch.
Related to:
MD32000 $MA_MAX_AX_VELO
(maximum axis velocity)
MD32050 $MA_JOG_REV_VELO
(revolutional feedrate for JOG)
MD32090 $MA_HANDWH_VELO_OVERLAY_FACTOR
(ratio of JOG velocity to handwheel velocity (DRF))
SD41110 $SN_JOG_SET_VELO
(JOG velocity for G94)
SD41130 $SN_JOG_ROT_AX_SET_VELO
(JOG velocity for rotary axes)
NC/PLC interface signal DB3200 DBX4 (Feedrate override A-H)
32040 JOG_REV_VELO_RAPID
mm/rev Revolutional feedrate in JOG with rapid traverse override
CTEQ
808d-me42 -
808d-me62 -
808d-te42 -
808d-te62 -
808d-mte40 -
808d-mte60 -
Description:
The value entered defines the revolutional feedrate of the axis in JOG mode with rapid
traverse override in relation to the revolutions of the master spindle. This feedrate
is active when SD41100 $SN_JOG_REV_IS_ACTIVE = 1. (Revolutional feedrate active with
JOG)
242
(2000./30), (2000./30), (0./ 0.)
(2000./30), (2000./30),
(2000./30), (200...
(2000./30), (2000./30), (0./ 0.)
(2000./30), (2000./30),
(2000./30), (200...
2.5, 2.5, 2.5, 1.0 0.0
2.5, 2.5, 2.5, 1.0, 1.0 0.0
2.5, 2.5, 2.5, 1.0 0.0
2.5, 2.5, 2.5, 1.0, 1.0, 0.0
1.0
2.5, 2.5, 2.5, 2.5, 2.5, 0.0
2.5, 2.5, 2.5...
2.5, 2.5, 2.5, 2.5, 2.5, 0.0
2.5, 2.5, 2.5...
(1.e300/ 1.e300) 2/2
(1.e300/ 1.e300) 2/2
A11, A04 H1, P2, R2, T1, V1, Z1
DOUBLE Reset
- 1/1
- 1/1
- 1/1
- 1/1
- 1/1
- 1/1
M
M
for linear axes,
M
M
M
M
M
M
Parameter Manual
List Manual, 01/2017