Siemens SINUMERIK 808D Parameter Manual page 146

Machine data
3.3 Channel-specific machine data
This machine data must refer to a valid base frame.
If its content is less than 0 or greater than or equal to the maximum number of base
frames set in MD28081 $MC_MM_NUM_BASE_FRAMES, selection of a corresponding tool holder
causes an alarm.
20188 TOCARR_FINE_LIM_LIN
mm Limit of linear fine offset TCARR
-
808d-me42 -
808d-me62 -
808d-te42 -
808d-te62 -
808d-mte40 -
808d-mte60 -
Description:
Indicates for each channel the input limit for the linear fine offset values of an
orientable tool holder.
20190 TOCARR_FINE_LIM_ROT
degrees Limit of rotary fine offset TCARR
-
808d-me42 -
808d-me62 -
808d-te42 -
808d-te62 -
808d-mte40 -
808d-mte60 -
Description:
Indicates for each channel the input limit for the rotary fine offset values of an
orientable tool holder.
20191 IGN_PROG_STATE_ASUP
- Do not display interrupt program execution on OPI
-
- -
Description:
The execution of the ASUB assigned to the interrupt is NOT displayed by the OPI
variables "progStatus" and "chanStatus".
Bit
Bit
...
Bit
Bit
146
1.0, 1.0, 1.0, 1.0, 1.0,
1.0, 1.0, 1.0...
1.0, 1.0, 1.0, 1.0, 1.0,
1.0, 1.0, 1.0...
1.0, 1.0, 1.0, 1.0, 1.0,
1.0, 1.0, 1.0...
1.0, 1.0, 1.0, 1.0, 1.0,
1.0, 1.0, 1.0...
1.0, 1.0, 1.0, 1.0, 1.0,
1.0, 1.0, 1.0...
1.0, 1.0, 1.0, 1.0, 1.0,
1.0, 1.0, 1.0...
1.0, 1.0, 1.0, 1.0, 1.0,
1.0, 1.0, 1.0...
1.0, 1.0, 1.0, 1.0, 1.0,
1.0, 1.0, 1.0...
1.0, 1.0, 1.0, 1.0, 1.0,
1.0, 1.0, 1.0...
1.0, 1.0, 1.0, 1.0, 1.0,
1.0, 1.0, 1.0...
1.0, 1.0, 1.0, 1.0, 1.0,
1.0, 1.0, 1.0...
1.0, 1.0, 1.0, 1.0, 1.0,
1.0, 1.0, 1.0...
0, 0, 0, 0, 0, 0, 0, 0...
0 = 1: Enable interrupt 1 (user interrupt)
1 = 1: Enable interrupt 2 (user interrupt)
7 = 1: Enable interrupt 8 (user interrupt)
8 = 1: Enable interrupt 9 (system interrupt, reserved)
C07
DOUBLE
0.0 -
0.0 -
0.0 -
0.0 -
0.0 -
0.0 -
C07
DOUBLE
0.0 -
0.0 -
0.0 -
0.0 -
0.0 -
0.0 -
EXP
DWORD
0 0x7FFFFFFF
W1
Immediately
7/3 M
7/3 M
7/3 M
7/3 M
0/0 M
0/0 M
W1
Immediately
7/3 M
7/3 M
7/3 M
7/3 M
0/0 M
0/0 M
K1
NEW CONF
2/2 M
Parameter Manual
List Manual, 01/2017