Siemens SINUMERIK 808D Parameter Manual page 162

Machine data
3.3 Channel-specific machine data
808d-mte40 5
808d-mte60 5
Description:
Smoothing of the programmed block end points with compressor type COMPCAD. Value 0: no
smoothing. Value 1: maximum smoothing.
Entry for all dynamic G code groups.
20487 COMPRESS_SMOOTH_FACTOR_2
- Smoothing by compressor
-
808d-me42 5
808d-me62 5
808d-te42 5
808d-te62 5
808d-mte40 5
808d-mte60 5
Description:
Extent to which the programmed block end points are smoothed in the case of compressor
type COMPCAD for non-geometry axes. Value 0: No smoothing. Value 1: Maximum smoothing.
Entry for each dynamic G code group.
20488 SPLINE_MODE
- Setting for spline interpolation
-
- -
Description:
This MD is used to determine the settings for spline interpolation. The allocation of
the spline segments to the NC blocks can thus be influenced. With spline
interpolation, the spline blocks are combined, if possible, in such a way, that there
are no blocks that are too short and could lead to a reduction in the possible path
velocity.
Bit 0: With BSPLINE, blocks that are too short are avoided.
Bit 1: With BSPLINE/ORICURVE, blocks that are too short are avoided.
Bit 2: With CSPLINE, blocks that are too short are avoided.
20490 IGNORE_OVL_FACTOR_FOR_ADIS
- G64x independent of overload factor
-
808d-me42 -
808d-me62 -
162
0., 0., 0., 0., 0., 0., 0., 0.
0., 0., 0., 0., 0., 0., 0.,
0., 0., ...
0., 0., 0., 0., 0., 0., 0., 0.
0., 0., 0., 0., 0., 0., 0.,
0., 0., ...
0., 0., 0., 0., 0., 0., 0., 0.
0., 0., 0., 0., 0., 0., 0.,
0., 0., ...
0., 0., 0.5, 0.5, 0.5 0.
0., 0., 0., 0., 0., 0., 0., 0.
0., 0., 0., 0., 0., 0., 0.,
0., 0., ...
0., 0., 0., 0., 0., 0., 0., 0.
0., 0., 0., 0., 0., 0., 0.,
0., 0., ...
0., 0., 0., 0., 0., 0., 0., 0.
0., 0., 0., 0., 0., 0., 0.,
0., 0., ...
0., 0., 0., 0., 0., 0., 0., 0.
0., 0., 0., 0., 0., 0., 0.,
0., 0., ...
0, 0, 0, 0, 0, 0, 0, 0... 0
FALSE, FALSE, 0
FALSE, FALSE,
FALSE, FALSE,
FALSE, FALSE...
TRUE 0
1. 1/1
1. 1/1
EXP, C05 B1
DOUBLE NEW CONF
1. 1/1
1. 1/1
1. 1/1
1. 1/1
1. 1/1
1. 1/1
EXP B1
BYTE NEW CONF
0x7 3/3
EXP B1
BOOLEAN NEW CONF
- 1/1
- 1/1
M
M
M
M
M
M
M
M
M
M
M
Parameter Manual
List Manual, 01/2017