Siemens SINUMERIK 808D Parameter Manual page 347

2:
1st axis turns around the x direction, the 2nd axis turns around the Y direction and,
if present, the 3rd axis turns around the new Z direction.
3:
1st axis turns around the Z direction, the 2nd axis turns around the Y direction and,
if present, the 3rd axis turns around the new X direction.
4:
$MC_ORIAX_TURN_TAB_1.
5:
$MC_ORIAX_TURN_TAB_2.
42690 JOG_CIRCLE_CENTRE
mm Center of the circle
-
808d-me42 3
808d-me62 3
808d-te42 3
808d-te62 3
808d-mte40 3
808d-mte60 3
Description:
This setting data is used to define the circle center point in the workpiece coordinate
system during JOG of circles.
Only the relevant center point coordinates of the geometry axes in the active plane
are evaluated, not the coordinate of the geometry axis vertical to the plane. This
setting data is written via the user interface.
By default the coordinate of an axis with diameter programming is in the diameter. This
can be changed with MD20360 $MC_TOOL_PARAMETER_DEF_MASK Bit 13 = 1 by indicating a
radius.
42691 JOG_CIRCLE_RADIUS
mm Circle radius
-
808d-me42 -
808d-me62 -
808d-te42 -
808d-te62 -
808d-mte40 -
808d-mte60 -
Description:
With this setting data, the circle radius in the machine, the maximum circle during
inner machining or the minimum circle during outer machining are defined when jogging
circles. This setting data is written via the user interface.
Parameter Manual
List Manual, 01/2017
RPY angles are traversed during jog with the turning sequence XYZ,
RPY angles are traversed during jog with the turning sequence ZYX,
The turning sequence of the rotary axes is set by means of MD21120
The turning sequence of the rotary axes is set by means of MD21130
0, 0, 0, 0, 0, 0, 0, 0, 0,
0, 0, 0, 0, 0, 0, 0, 0, 0,
0, 0, 0, 0...
0, 0, 0, 0, 0, 0, 0, 0, 0,
0, 0, 0, 0, 0, 0, 0, 0, 0,
0, 0, 0, 0...
0, 0, 0, 0, 0, 0, 0, 0, 0,
0, 0, 0, 0, 0, 0, 0, 0, 0,
0, 0, 0, 0...
0, 0, 0, 0, 0, 0, 0, 0, 0,
0, 0, 0, 0, 0, 0, 0, 0, 0,
0, 0, 0, 0...
0, 0, 0, 0, 0, 0, 0, 0, 0,
0, 0, 0, 0, 0, 0, 0, 0, 0,
0, 0, 0, 0...
0, 0, 0, 0, 0, 0, 0, 0, 0,
0, 0, 0, 0, 0, 0, 0, 0, 0,
0, 0, 0, 0...
0, 0, 0, 0, 0, 0, 0, 0...
0, 0, 0, 0, 0, 0, 0, 0...
0, 0, 0, 0, 0, 0, 0, 0...
0, 0, 0, 0, 0, 0, 0, 0...
0, 0, 0, 0, 0, 0, 0, 0...
0, 0, 0, 0, 0, 0, 0, 0...
-
DOUBLE
- -
- -
- -
- -
- -
- -
-
DOUBLE
- -
- -
- -
- -
- -
- -
NC setting data
that is the
that is the
-
Immediately
2/2 M
2/2 M
2/2 M
2/2 M
7/7 U
7/7 U
-
Immediately
2/2 M
2/2 M
2/2 M
2/2 M
7/7 U
7/7 U
347