Siemens SINUMERIK 808D Parameter Manual page 358

NC setting data
42970 TOFF_LIMIT
mm Upper limit of correction value via $AA_TOFF
-
808d-me42 3
808d-me62 3
808d-te42 3
808d-te62 3
808d-mte40 3
808d-mte60 3
Description:
Upper limit of the offset value which can be defined by means of synchronized actions
via the $AA_TOFF system variable.
This limit value influences the absolutely effective amount of offset through $AA_TOFF.
Whether the offset value is within the limit range can be checked via the
$AA_TOFF_LIMIT system variable.
42972 TOFF_LIMIT_MINUS
mm Lower limit of the offset value $AA_TOFF
-
808d-me42 3
808d-me62 3
808d-te42 3
808d-te62 3
808d-mte40 3
808d-mte60 3
Description:
Lower limit of the offset value which can be specified through synchronous actions via
the system variable $AA_TOFF.
This limit value acts on the active correction through $AA_TOFF in the minus direction.
This limit value is only effective if $MC_TOFF_MODE Bit6 = 1 is set.
Über die Systemvariable $AA_TOFF_LIMIT kann abgefragt werden, ob sich der
Korrekturwert im Grenzbereich befindet.
358
10.0, 10.0, 10.0, 10.0, 0.0
10.0, 10.0, 10.0, 10.0,
10.0, 10.0, 10.0...
10.0, 10.0, 10.0, 10.0, 0.0
10.0, 10.0, 10.0, 10.0,
10.0, 10.0, 10.0...
10.0, 10.0, 10.0, 10.0, 0.0
10.0, 10.0, 10.0, 10.0,
10.0, 10.0, 10.0...
10.0, 10.0, 10.0, 10.0, 0.0
10.0, 10.0, 10.0, 10.0,
10.0, 10.0, 10.0...
10.0, 10.0, 10.0, 10.0, 0.0
10.0, 10.0, 10.0, 10.0,
10.0, 10.0, 10.0...
10.0, 10.0, 10.0, 10.0, 0.0
10.0, 10.0, 10.0, 10.0,
10.0, 10.0, 10.0...
0.0, 0.0, 0.0, 0.0, 0.0, -
0.0, 0.0, 0.0, 0.0, 0.0,
0.0, 0.0, 0.0,...
0.0, 0.0, 0.0, 0.0, 0.0, -
0.0, 0.0, 0.0, 0.0, 0.0,
0.0, 0.0, 0.0,...
0.0, 0.0, 0.0, 0.0, 0.0, -
0.0, 0.0, 0.0, 0.0, 0.0,
0.0, 0.0, 0.0,...
0.0, 0.0, 0.0, 0.0, 0.0, -
0.0, 0.0, 0.0, 0.0, 0.0,
0.0, 0.0, 0.0,...
0.0, 0.0, 0.0, 0.0, 0.0, -
0.0, 0.0, 0.0, 0.0, 0.0,
0.0, 0.0, 0.0,...
0.0, 0.0, 0.0, 0.0, 0.0, -
0.0, 0.0, 0.0, 0.0, 0.0,
0.0, 0.0, 0.0,...
- F2
DOUBLE Immediately
- 0/0
- 0/0
- 0/0
- 0/0
- 7/7
- 7/7
- F2
DOUBLE Immediately
0.0 0/0
0.0 0/0
0.0 0/0
0.0 0/0
0.0 7/7
0.0 7/7
S
S
S
S
U
U
S
S
S
S
U
U
Parameter Manual
List Manual, 01/2017