Siemens CU240B-2 Parameter Manual page 482

Parameters
Connector/Binector (BICO)-Parameters
r2120
r2121
r2131
r2132
r2169
p2201[0...n]
p2202[0...n]
p2203[0...n]
p2204[0...n]
p2205[0...n]
p2206[0...n]
p2207[0...n]
p2208[0...n]
p2209[0...n]
p2210[0...n]
p2211[0...n]
p2212[0...n]
p2213[0...n]
p2214[0...n]
p2215[0...n]
r2224
r2245
r2250
r2260
r2262
r2266
r2272
r2273
p2291
p2292
r2294
p2295
r2344
p2900[0...n]
p2901[0...n]
r2902[0...14]
p2930[0...n]
r3131
r3132
r9733[0...2]
r20095
r20099
r20103
r20107
r20111
r20115
r20119[0...2]
r20124[0...2]
r20129
r20134
r20220
r20225
r20231
1-482
CO: Sum of fault and alarm buffer changes / Sum buffer changed
CO: Counter, alarm buffer changes / Alrm buff changed
CO: Actual fault code / Actual fault code
CO: Actual alarm code / Actual alarm code
CO: Actual speed smoothed signals / n_act smth message
CO: Technology controller, fixed value 1 / Tec_ctr fix val 1
CO: Technology controller, fixed value 2 / Tec_ctr fix val 2
CO: Technology controller, fixed value 3 / Tec_ctr fix val 3
CO: Technology controller, fixed value 4 / Tec_ctr fix val 4
CO: Technology controller, fixed value 5 / Tec_ctr fix val 5
CO: Technology controller, fixed value 6 / Tec_ctr fix val 6
CO: Technology controller, fixed value 7 / Tec_ctr fix val 7
CO: Technology controller, fixed value 8 / Tec_ctr fix val 8
CO: Technology controller, fixed value 9 / Tec_ctr fix val 9
CO: Technology controller, fixed value 10 / Tec_ctr fix val 10
CO: Technology controller, fixed value 11 / Tec_ctr fix val 11
CO: Technology controller, fixed value 12 / Tec_ctr fix val 12
CO: Technology controller, fixed value 13 / Tec_ctr fix val 13
CO: Technology controller, fixed value 14 / Tec_ctr fix val 14
CO: Technology controller, fixed value 15 / Tec_ctr fix val 15
CO: Technology controller, fixed value effective / Tec_ctr FixVal eff
CO: Technology controller mot. potentiometer setpoint before RFG / Tec_ctr mop befRFG
CO: Technology controller motorized potentiometer setpoint after RFG / Tec_ctr mop aftRFG
CO: Technology controller setpoint after ramp-function generator / Tec_ctr set aftRFG
CO: Technology controller setpoint after filter / Tec_ctr set aftFlt
CO: Technology controller actual value after filter / Tec_ctr act aftFlt
CO: Technology controller actual value scaled / Tech_ctrl act scal
CO: Technology controller error / Tec_ctrl error
CO: Technology controller maximum limiting / Tec_ctrl max_limit
CO: Technology controller minimum limiting / Tec_ctrl min_lim
CO: Technology controller output signal / Tec_ctrl outp_sig
CO: Technology controller output scaling / Tec_ctrl outp scal
CO: Technology controller last speed setpoint (smoothed) / Tec_ctrl n_setp_sm
CO: Fixed value 1 [%] / Fixed value 1 [%]
CO: Fixed value 2 [%] / Fixed value 2 [%]
CO: Fixed values [%] / Fixed values [%]
CO: Fixed value M [Nm] / Fixed value M [Nm]
CO: Current flt value / Current flt value
CO: Actual component number / Act comp_no.
CO: SI Motion setpoint speed limit effective / SI Mtn setp_lim
CO: ADD 0 output Y / ADD 0 output Y
CO: ADD 1 output Y / ADD 1 output Y
CO: SUB 0 difference Y / SUB 0 difference Y
CO: SUB 1 difference Y / SUB 1 difference Y
CO: MUL 0 product Y / MUL 0 product Y
CO: MUL 1 product Y / MUL 1 product Y
CO: DIV 0 quotient / DIV 0 quotient
CO: DIV 1 quotient / DIV 1 quotient
CO: AVA 0 output Y / AVA 0 output Y
CO: AVA 1 output Y / AVA 1 output Y
CO: NSW 0 output Y / NSW 0 output Y
CO: NSW 1 output Y / NSW 1 output Y
CO: LIM 0 output Y / LIM 0 output Y
SINAMICS G120 / Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
© Siemens AG 2011 All Rights Reserved