Siemens CU240B-2 Parameter Manual page 336
Hide thumbs
Also See for CU240B-2:
- Operating instructions manual (36 pages) ,
- Compact operating instructions (32 pages)
Table of Contents
Advertisement
Parameters
List of Parameters
p9321[0...7]
SI Motion gearbox motor/load denominator (processor 2) / SI Mtn gear den P2
CU240E-2 DP F
Access level: 3
CU240E-2 F
Can be changed: C(95)
Units group: -
Min
1
Description:
Sets the denominator for the gearbox between the motor and the load.
Index:
[0] = Gearbox 1
[1] = Gearbox 2
[2] = Gearbox 3
[3] = Gearbox 4
[4] = Gearbox 5
[5] = Gearbox 6
[6] = Gearbox 7
[7] = Gearbox 8
Dependency:
Refer to: p9322
Notice:
It is not possible to change over the gearbox stages. Gearbox 1 (index 0) is always active.
p9322[0...7]
SI Motion gearbox motor/load numerator (processor 2) / SI Mtn gear num P2
CU240E-2 DP F
Access level: 3
CU240E-2 F
Can be changed: C(95)
Units group: -
Min
1
Description:
Sets the numerator for the gearbox between the motor and the load.
Index:
[0] = Gearbox 1
[1] = Gearbox 2
[2] = Gearbox 3
[3] = Gearbox 4
[4] = Gearbox 5
[5] = Gearbox 6
[6] = Gearbox 7
[7] = Gearbox 8
Dependency:
Refer to: p9321
Notice:
It is not possible to change over the gearbox stages. Gearbox 1 (index 0) is always active.
Note:
In the case of encoderless monitoring functions, the pole pair number must be multiplied by the numerator of the
gearbox ratio.
Example:
Gearbox ratio 1:4, pole pair number (r0313) = 2
--> p9321 = 1, p9322 = 8 (4 x 2)
p9331[0...3]
SI Motion SLS limit values (processor 2) / SI Mtn SLS lim P2
Access level: 3
CU240E-2 DP F
Can be changed: C(95)
CU240E-2 F
Units group: -
Min
0.01 [rpm]
Description:
Sets the limit values for the function "Safely-Limited Speed" (SLS).
Index:
[0] = Limit value SLS1
[1] = Limit value SLS2
[2] = Limit value SLS3
[3] = Limit value SLP4
Dependency:
Refer to: p9363, p9531
Refer to: C01714
Notice:
This parameter is overwritten by the copy function of the safety functions integrated in the drive.
Note:
SLS: Safely-Limited Speed
1-336
Calculated: -
Scaling: -
Unit selection: -
Max
2147000000
Calculated: -
Scaling: -
Unit selection: -
Max
2147000000
Calculated: -
Scaling: -
Unit selection: -
Max
100000.00 [rpm]
SINAMICS G120 / Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
Data type: Unsigned32
Data set: -
Factory setting
1
Data type: Unsigned32
Data set: -
Factory setting
1
Data type: FloatingPoint32
Data set: -
Factory setting
2000.00 [rpm]
© Siemens AG 2011 All Rights Reserved
Hide quick links:
Advertisement
Table of Contents
