Siemens CU240B-2 Parameter Manual page 469

p1703[0...n]
p1715[0...n]
p1717[0...n]
p1726[0...n]
p1727[0...n]
p1730[0...n]
p1740[0...n]
p1745[0...n]
p1750[0...n]
p1755[0...n]
p1758[0...n]
p1759[0...n]
p1764[0...n]
p1767[0...n]
p1774[0...n]
p1775[0...n]
p1780[0...n]
p1784[0...n]
p1785[0...n]
p1786[0...n]
r1787[0...n]
p1795[0...n]
r1797[0...n]
p1800[0...n]
p1802[0...n]
p1803[0...n]
p1806[0...n]
p1820[0...n]
p1959[0...n]
p2140[0...n]
p2141[0...n]
p2142[0...n]
p2149[0...n]
p2150[0...n]
p2152[0...n]
p2153[0...n]
p2155[0...n]
p2156[0...n]
p2157[0...n]
p2158[0...n]
p2159[0...n]
p2160[0...n]
p2161[0...n]
p2162[0...n]
p2163[0...n]
p2164[0...n]
p2166[0...n]
p2167[0...n]
p2170[0...n]
p2171[0...n]
p2172[0...n]
p2173[0...n]
p2174[0...n]
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
Isq current controller pre-control scaling / Isq_ctr_prectrScal
Current controller P gain / I_ctrl Kp
Current controller integral-action time / I_ctrl Tn
Quadrature arm decoupling, scaling / Transv_decpl scal
Quadrature arm decoupling at voltage limit scaling / TrnsvDecplVmaxScal
Isd controller integral component shutdown threshold / Isd_ctrl I_thresh
Gain resonance damping for encoderless closed-loop control / Gain res_damp
Motor model error threshold stall detection / MotMod ThreshStall
Motor model configuration / MotMod config
Motor model changeover speed encoderless operation / MotMod n_chgSnsorl
Motor model changeover delay time closed/open-loop control / MotMod t cl_op
Motor model changeover delay time open/closed-loop control / MotMod t op_cl
Motor model without encoder speed adaptation Kp / MotMod woE n_adaKp
Motor model without encoder speed adaptation Tn / MotMod woE n_adaTn
Motor model, offset voltage compensation alpha / MotMod offs comp A
Motor model, offset voltage compensation beta / MotMod offs comp B
Motor model adaptation configuration / MotMod adapt conf
Motor model feedback scaling / Mod_FB_scal
Motor model Lh adaptation Kp / MotMod Lh Kp
Motor model Lh adaptation integral time / MotMod Lh Tn
Motor model Lh adaptation corrective value / MotMod Lh corr
Motor model kT adaptation integral time / MotMod kT Tn
Motor model kT adaptation corrective value / MotMod kT corr
Pulse frequency setpoint / Pulse freq setp
Modulator mode / Modulator mode
Maximum modulation depth / Modulat depth max
Filter time constant Vdc correction / T_filt Vdc_corr
Reverse the output phase sequence / Outp_ph_seq rev
Rotating measurement configuration / Rot meas config
Hysteresis speed 2 / n_hysteresis 2
Speed threshold 1 / n_thresh val 1
Hysteresis speed 1 / n_hysteresis 1
Monitoring configuration / Monit config
Hysteresis speed 3 / n_hysteresis 3
Delay for comparison n > n_max / Del n > n_max
Speed actual value filter time constant / n_act_filt T
Speed threshold 2 / n_thresh val 2
On delay, comparison value reached / t_on cmpr val rchd
Speed threshold 5 / n_thresh val 5
Delay for n_act comparison with speed threshold value 5 / Del compar n_5
Speed threshold 6 / n_thresh val 6
Delay for n_act comparison with speed threshold value 6 / Del compar n_6
Speed threshold 3 / n_thresh val 3
Hysteresis speed n_act > n_max / Hyst n_act>n_max
Speed threshold 4 / n_thresh val 4
Hysteresis speed 4 / n_hysteresis 4
Off delay n_act = n_set / t_del_off n_i=n_so
Switch-on delay n_act = n_set / t_on n_act=n_set
Current threshold value / I_thres
Current threshold value reached delay time / t_del I_thresh rch
DC link voltage, threshold value / Vdc thresh val
DC link voltage comparison delay time / t_del Vdc
Torque threshold value 1 / M_thresh val 1
Command and Drive Data Sets – Overview
Parameters
1-469