Siemens CU240B-2 Parameter Manual page 480

Parameters
Connector/Binector (BICO)-Parameters
r0034
r0035
r0036
r0037[0...19]
r0060
r0062
r0063[0...2]
r0064
r0066
r0067
r0068[0...1]
r0069[0...6]
r0070
r0072
r0074
r0075
r0076
r0077
r0078
r0079
r0080[0...1]
r0081
r0082[0...2]
r0083
r0084[0...1]
r0087
r0094
r0289
r0586
r0587
r0588
r0752[0...1]
r0755[0...1]
r0944
p1001[0...n]
p1002[0...n]
p1003[0...n]
p1004[0...n]
p1005[0...n]
p1006[0...n]
p1007[0...n]
p1008[0...n]
p1009[0...n]
p1010[0...n]
p1011[0...n]
p1012[0...n]
p1013[0...n]
p1014[0...n]
p1015[0...n]
r1024
r1045
r1050
r1073
1-480
CO: Motor utilization / Motor utilization
CO: Motor temperature / Mot temp
CO: Power unit overload I2t / PU overload I2t
CO: Power unit temperatures / PU temperatures
CO: Speed setpoint before the setpoint filter / n_set before filt.
CO: Speed setpoint after the filter / n_set after filter
CO: Speed actual value / n_act
CO: Speed controller system deviation / n_ctrl system dev
CO: Output frequency / f_outp
CO: Output current, maximum / I_outp max
CO: Absolute current actual value / I_act abs val
CO: Phase current actual value / I_phase act value
CO: Actual DC link voltage / Vdc act val
CO: Output voltage / U_output
CO: Modulat_depth / Modulat_depth
CO: Current setpoint field-generating / Id_set
CO: Current actual value field-generating / Id_act
CO: Current setpoint torque-generating / Iq_set
CO: Current actual value torque-generating / Iq_act
CO: Torque setpoint / M_set total
CO: Torque actual value / M_act
CO: Torque utilization / M_Utilization
CO: Active power actual value / P_act
CO: Flux setpoint / Flex setp
CO: Flux actual value / Flux act val
CO: Actual power factor / Cos phi act
CO: Transformation angle / Transformat_angle
CO: Maximum power unit output current / PU I_outp max
CO: Measuring probe, speed actual value / MT n_act
CO: Measuring probe, measuring time measured / MT t_meas measured
CO: Measuring probe, pulse counter / MT pulse counter
CO: CU analog inputs input voltage/current actual / CU AI U/I_inp act
CO: CU analog inputs actual value in percent / CU AI value in %
CO: Counter for fault buffer changes / Fault buff change
CO: Fixed speed setpoint 1 / n_set_fixed 1
CO: Fixed speed setpoint 2 / n_set_fixed 2
CO: Fixed speed setpoint 3 / n_set_fixed 3
CO: Fixed speed setpoint 4 / n_set_fixed 4
CO: Fixed speed setpoint 5 / n_set_fixed 5
CO: Fixed speed setpoint 6 / n_set_fixed 6
CO: Fixed speed setpoint 7 / n_set_fixed 7
CO: Fixed speed setpoint 8 / n_set_fixed 8
CO: Fixed speed setpoint 9 / n_set_fixed 9
CO: Fixed speed setpoint 10 / n_set_fixed 10
CO: Fixed speed setpoint 11 / n_set_fixed 11
CO: Fixed speed setpoint 12 / n_set_fixed 12
CO: Fixed speed setpoint 13 / n_set_fixed 13
CO: Fixed speed setpoint 14 / n_set_fixed 14
CO: Fixed speed setpoint 15 / n_set_fixed 15
CO: Fixed speed setpoint effective / n_set_fixed eff
CO: Mot. potentiometer speed setp. in front of ramp-fct. gen. / Mop n_set bef RFG
CO: Motor. potentiometer setpoint after the ramp-function generator / Mop setp after RFG
CO: Main setpoint effective / Main setpoint eff
SINAMICS G120 / Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
© Siemens AG 2011 All Rights Reserved