Siemens CU240B-2 Parameter Manual page 472

Parameters
Command and Drive Data Sets – Overview
p0354[0...n]
p0356[0...n]
p0357[0...n]
p0358[0...n]
p0360[0...n]
p0362[0...n]
p0363[0...n]
p0364[0...n]
p0365[0...n]
p0366[0...n]
p0367[0...n]
p0368[0...n]
p0369[0...n]
r0370[0...n]
r0372[0...n]
r0373[0...n]
r0374[0...n]
r0376[0...n]
r0377[0...n]
r0378[0...n]
r0382[0...n]
r0384[0...n]
r0386[0...n]
r0395[0...n]
r0396[0...n]
p0601[0...n]
p0604[0...n]
p0605[0...n]
p0606[0...n]
p0607[0...n]
p0610[0...n]
p0611[0...n]
p0612[0...n]
p0615[0...n]
p0620[0...n]
p0621[0...n]
p0622[0...n]
p0625[0...n]
p0626[0...n]
p0627[0...n]
p0628[0...n]
r0630[0...n]
r0631[0...n]
r0632[0...n]
r0633[0...n]
p0634[0...n]
p0635[0...n]
p0636[0...n]
p0637[0...n]
p0650[0...n]
p0651[0...n]
p0826[0...n]
p1231[0...n]
1-472
Motor rotor resistance cold / Mot R_r cold
Motor stator leakage inductance / Mot L_stator leak.
Motor stator inductance, d axis / Mot L_stator d
Motor rotor leakage inductance / Mot L_rot leak
Motor magnetizing inductance / Mot Lh
Motor saturation characteristic flux 1 / Mot saturat.flux 1
Motor saturation characteristic flux 2 / Mot saturat.flux 2
Motor saturation characteristic flux 3 / Mot saturat.flux 3
Motor saturation characteristic flux 4 / Mot saturat.flux 4
Motor saturation characteristic I_mag 1 / Mot sat. I_mag 1
Motor saturation characteristic I_mag 2 / Mot sat. I_mag 2
Motor saturation characteristic I_mag 3 / Mot sat. I_mag 3
Motor saturation characteristic I_mag 4 / Mot sat. I_mag 4
Motor stator resistance, cold / Mot R_stator cold
Cable resistance / Mot R_cable
Motor rated stator resistance / Mot R_stator rated
Motor rotor resistance cold / Mot R_r cold
Rated motor rotor resistance / Mot R_rotor rated
Motor leakage inductance, total / Mot L_leak total
Motor stator inductance, d axis / Mot L_stator_d
Motor magnetizing inductance transformed / Mot L_magn transf
Motor rotor time constant / damping time constant d axis / Mot T_rotor/T_Dd
Motor stator leakage time constant / Mot T_stator leak
Actual stator resistance / R_stator act
Actual rotor resistance / R_rotor act
Motor temperature sensor type / Mot_temp_sens type
Motor temperature alarm threshold / Mot_temp al thr
Motor temperature fault threshold / Mot_temp flt thr
Motor temperature timer / Mot_temp timer
Temperature sensor fault timer / Sensor fault time
Motor overtemperature response / Mot temp response
I2t motor model thermal time constant / I2t mot_mod T
Thermal motor model configuration / Therm Mot_mod conf
I2t motor model fault threshold / I2t mot_mod thresh
Thermal adaptation, stator and rotor resistance / Mot therm_adapt R
Identification stator resistance after restart / Rst_ident Restart
Motor excitation time for Rs_ident after powering up again / t_excit Rs_id
Motor ambient temperature / Mot T_ambient
Motor overtemperature, stator core / Mot T_over core
Motor overtemperature, stator winding / Mot T_over stator
Motor overtemperature rotor winding / Mot T_over rotor
Motor temperature model ambient temperature / MotTMod T_amb.
Motor temperature model, stator core temperature / MotTMod T_core
Motor temperature model, stator winding temperature / MotTMod T_copper
Motor temperature model, rotor temperature / MotTMod T_rotor
Q flux flux constant unsaturated / PSIQ KPSI UNSAT
Q flux quadrature axis current constant unsaturated / PSIQ KIQ UNSAT
Q flux direct axis current constant unsaturated / PSIQ KID UNSAT
Q flux flux gradient saturated / PSIQ Grad SAT
Actual motor operating hours / Mot t_oper act
Motor operating hours maintenance interval / Mot t_op maint
Motor changeover, motor number / Mot_chng mot No.
DC braking configuration / DCBRK config
SINAMICS G120 / Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
© Siemens AG 2011 All Rights Reserved