Acura 1994 Integra Service Manual page 380

72 mm Thrust Shim
Part Number Thickness
23931 - P21 -000 0.60 mm (0.0236 in)
2 3 9 3 2 - P 2 1 - 0 0 0
0.63 mm (0.0248 in)
c 23933 - P21 -000
0.66 mm {0.0260 in}
D
2 3 9 3 4 - P 2 1 - 0 0 0
0.69 mm (0.0272 in)
23935 - P21 -000
0.72 mm (0.0283 in)
F
2 3 9 3 6 - P 2 1 - 0 0 0
0.75 mm (0.0295 in)
2 3 9 3 7 - P 2 1 - 0 0 0
0.78 mm (0.0307 in)
2 3 9 3 8 - P 2 1 - 0 0 0
0.81 mm (0.0319 in)
2 3 9 3 9 - P 2 1 - 0 0 0
0.84 mm (0.0331 in)
J
2 3 9 4 0 - P 2 r - 0 0 0
0.87 mm (0.0343 in)
K
23941 - P21 -000 0.90 mm (0.0354 in)
L
23912-P21-OOO
0.93 mm (0.0366 in)
M
2 3 9 4 3 - P 2 1 - 0 0 0
0.96 mm (0.0378 in)
N
2 3 9 4 4 - P 2 1 - 0 0 0
0.99 mm (0.0390 in)
o 23915 - P21 -000
1.02 mm (0.0402 in)
P
23946 - P21 ,000 1.05 mm (0.04'13 in)
o
23947 -P21 -000
1.08 mm (0.0425 in)
23948 - P21 000
1.11 mm {0.0437 in}
s
2 3 9 1 9 - P 2 1 - 0 0 0 1.14 mm (0.0449 inl
T
2 3 9 5 0 - P 2 1 - 0 0 0
1.17 mm (0.0461 in)
23951 - P21 -000
1.20 mm {0.0472 in)
23952 - P21 000
1.23 mm {0.0484 in)
2 3 9 5 3 - P 2 1 - 0 0 0
1.26 mm (0.0496 in)
X
2 3 9 5 4 - P 2 r - 0 0 0
1.29 mm 10.0508 in)
2 3 9 5 5 - P 2 1 - 0 0 0
1.32 mm 10.0520 in)
z 2 3 9 s 6 - P 2 1 , 0 0 0
1.35 mm (0.0531 in)
2 3 9 5 7 - P 2 1 - 0 0 0 1.38 mm (0.0543 inl
AB
23958 - P21 -000 1.41 mm (0.0555 in)
AC
23959 - P21 -000 1.44 mm (0.0567 in)
AD
23960 - P21 -000
1.47 mm (0.0579 in)
AE
23961 -P21 -000
1.50 mm {0.0591 in)
23962 P21 ,000
1.53 mm {0.0602 in)
2 3 9 6 3 - P 2 1 - 0 0 0
1.56 mm {0.0614 in}
A H
23964 - P2'1 -000 1.59 mm (0.0626 in)
AI
23965 - P2'1 -000
1.62 mm (0.0638 in)
2 3 9 6 6 - P 2 1 - 0 0 0
1.65 mm (0.0650 in)
AK
2 3 9 6 7 - P 2 1 - 0 0 0
1.68 mm {0.0661 in)
23968 - P21 -000
1.71 mm 10.0673 in)
23969 - P21 000 1.74 mm (0.0685 in)
A N
2 3 9 7 0 - P 2 1 - 0 0 0
'1.77 mm (0.0697 in)
AO 23971 P21 000
1.80 mm (0.0709 in)
7. Check the thrust clearance in the manner described
below.
NOTE: Carry out the measurement at normal room
remperarure.
-1. Install the thrust shim selected and oil guide
plate in th€ transmission housing.
?2 mm THRUST otL PLATE
TRANSMISSION
HOUSING
I n s t a l l t h e s p r i n g
ball bearing.
w a s h e r a n d w a s h e r o n t h e
NOTE:
. Clean the spring washer, washer and thrust shim
throughly before instaliation.
. I n s t a l l t h e s p r i n g w a s h e r . w a s h e r a n d t h r u s t
shim properly.
a-=s-.r*os".^
.,,-B*^INGWASHER
- 4 .
Installthe mainshaft in the clutch housing.
Place the transmission housing over the main-
shaft and onto the clutch housing.
Tighten the clutch and transmission housings
with severalS mm bolts.
NOTE: lt is not necessary to use sealing agent
between the housings.
8 x 1.25 mm
27 N.m {2.8 kgf.m, 20 lbf.ft}
Tap the mainshaft with a plastic hammer,
(cont'd)
1 3 - 3 9