Acura 1994 Integra Service Manual page 21

E
BI k (818C1 Section 7
Unit of length: mm (in)
ngrne ]'ocK (ltluur englnel -
MEASUREMENT
STANDARD (NEWI
SERVIC€ LIMIT
Cyiinder block
warpage of deck surlace
Bore diameter
Bore taPer
Reboring limit
0.05 (0.002) max.
81.00 - 81.02 {3.189 - 3.190)
0.08 (0.003)
8 1 . 0 7 1 3 . 1 9 2 )
0.05 (0.002)
0.25 (0.010)
Piston
Skin O.D. ar 15 mm (0.6 in) {rom bottom ot skirt
Clearance in cylinder
Groove width (For ring)
ToP
Socond
o i l
80.98 - 80.99 13.188 - 3.189)
0.0r - 0.04 {0.0004 - 0.0016}
1.030 - 1.0,r0 {0.0406 - 0.0409)
1.230 - 1.240 (0.0484 - 0.0488)
2.805 - 2.820 (0.1104 - 0.11101
80.97 (3.188)
0.05 (0.002)
1.060 (0.0417)
1.260 (0.0496)
2 . 8 4 0 ( 0 . 1 1 1 8 )
Piston ring
Ring-to-pistongrooveclearance Top
Second
0.045 - 0.070 {0.0018 - 0.0028}
0.010 - 0.065 (0.0016 - 0.0026)
0.13 (0.005)
0.13 (0.005)
Ring end gap
I oP
Socond
oil
0.20 - 0.35 {0.008 - 0.014)
0.40 - 0,55 (0.016 - 0.022)
0.20 - 0.s0 {0.008 - 0.020}
0.60 (0.024)
0.70 (0.028)
0.7010.0281
rrston rtn
o.D.
Pin-to-piston clearance
20.994 - 21.000 (0.8265 - 0.8268)
0.010 - 0.022 {0.0004 - 0.0009)
0.017 - 0.035 (0.0007 - 0.0014)
20.964 - 20.997 (0.8254 - 0.8267)
€.0 (1.89)
0.15 - 0.30 (0.006 - 0.012)
Connecting rod
Pin to-rod int€rference
Small end bore diameter
Large end bore diameter
Nominal
End play installed on crankshaft
crankshatt
N o . 1 , 2 , 4 a n d 5 i o u r n a l s
No. 3 journal
Rod iournal diameter
Taper
Out'ol round
End play
Runout
Msin journal diameter
54.976 - 55.000 (2.1644 - 2.16541
54.974 - 54.998 (2.'|643 - 2.1553)
44.976 - 45.000 {1.7707 -' I.7717)
0.005 {0.0002} max.
0.004 {0.0002) max.
0.10 - 0.35 {0.00{ - 0.014)
0.020 (0.0008) max.
-t-oou
lo.ooort
Eearing
Main bsaring-to-journal oil clearance
No. 1, 2, 4 and 5 journals
No 3 journal
Rod bearing-to-journal
oil clearanc€
0.024 - 0.042 (0.0009 - 0.0017)
0.030 - 0.048 (0.0012 - 0.0019)
0.032 - 0.050 (0.0013 - 0.0020)
0.050 (0.0020)
0.060 {0.0024)
0.060 (0.0024)
3-5