Acura 1994 Integra Service Manual page 25

MEASUREMENI
STANDARD INEW)
SERVICE LIMIT
Reverse idler
g e a r ' 1
L D .
Gear-to-reverse gear shaft clearance
20.016 - 20.043 (0.7880 - 0.7891)
0.036 - 0.084 (0.0014 - 0.0033)
20.09 (0.7909)
0.16 (0.006)
Synchro ring
Ring-to-gear clearance (ring pushed against 99ar)
0.85 - 1.10 (0.033 - 0.043) 0.4 (0.0't6)
O o u b l e c o n e
s y n c h r o r i n g * 2
Clearance {rin9 pushed against gear)
Outer synchro ring-to-gear
lnner synchro ring-to-gear
Outer synchro ring-to-synchro cone
0.95 r 1.68 (0.037 - 0.066)
0.5 - 1.0 (0.02 - 0.04)
0.5- 1.0 {0.02 -0.04)
0.6 (0.024)
0 . 3 ( 0 . 0 1 )
0.3 (0.01)
Sh itt fork
Shift tork finger thickness
Fork-to synchro sleeve clearance
7.4,7.6 (0.291 - 0.299)
0.35 - 0.65 (0.014 - 0.026) 1.0 (0.039)
qeverse shift
Shift fork pawl groove width
Fork-to-reverse idler gear clearance
"1" groove width
at sth gear side
at reverse gear side
Fork-to-5th/reverse shift piece pin clearance
at 5th gear side
at reverse gear side
13.0 - 13.3 (0.512 - 0.524)
0.5 - 1.1 10.020 - 0.043)
7.40 - 7.70 (0.291 -0.303)
7.05 - 7.25 (0.278 - 0.28s)
0.4 - 0.9 {0.016 - 0.03s)
0.05 - 0.45 (0.0020 - 0.018)
13907)
S h i f t a r m
Groove width of change piece contact area
Change piece-to-shift arm clearance
11.8 - 12.0 (0.4646- 0.4724)
0.05 - 0.35 (0.002 - 0.014)
0.8010.031)
S h i f t p i e c e
Groove width of shift arm contact area
Shift piece'to-shift arm clearance
L D .
Shift piece-to-shaft clearance
Diameter of shift Iork cont6ct area
Shift piece-to-shift fork shaft clearance
7.9 - 8.0 (0.311 -0.315)
0.10 - 0.30 (0.004 - 0.012)
14.000 - 14.068 {0.551 - 0.554)
0.011-0.092 (0.0004 - 0.0036,
1'1.90 - 12.00 (0.469 - 0.472)
0.20 - 0.50 (0.008 - 0.020i
0.60 (0.024)
0.150 (0.0059)
oso to.oart
S e l e c t o r
Diameter of change piece contact area
Arm-to-change piece clearance
Groove widlh of interlock contact area
Arm-to-interlock clearance
11.90 - ' t2.00 (0.469 - 0.472)
0.05 - 0.35 {0.002 - 0.014)
10.05 - 10.15 {0.3957 - 0.3996}
0.05 - 0.2s (0.002 - 0.010)
0.50 (0.020)
0.50 (0.020)
Manual Transmission
Section 13
' 1 : 8 1 8 8 1 e n g i n e
'2 818C1 engine
- Automatic Transmission Section 14
Unit of length: mm (in)
(cont'd)
-
o E u t r l r r l
r r
MEASUREMENT
STANDARD {NEWI
SERVICE LIMIT
Transmission
l l u i d
Capacity
I (US qt, lmp qt)
5.9 16.2, 5.2)for overhaul
2.7 (2.9, 2.4) for lluid change
Hydraulic
pressure
I kPa lkgflcm', psi)
Line pressure at 2,000 rpm
(E or E position)
830 - 880 (8.5 - 9.0, 120 - 130)
780 {8.0, 110)
2nd clutch pressure at 2,000 rpm
(DJ position)
460 - 14.7, 67)
throttle Iully closed
I
I
830 - 880 (8.5 - 9.0, 120 - 130)
throttle more than 3/16 opened
4 1 0 { 4 . 2 . 6 0 )
throttle fully closed
I
780 {8.0, 110)
throttle more than
3/16 opened
3rd clutch pressure at 2,000 rpm
(lqr posirion)
4th clutch pressure at 2,000 rPm
{E position)
2nd clutch pressure at 2,000 rPm
(Elposition)
830 - 880 {8.s - 9.0. 120 130)
780 (8.0, 110)
1st clutch pressure at 2,000 rpm
([O or E position)
830 - 880 (8.5 - 9.0, 120 - 130) 780 (8.0, 110)
'lst'hold clutch pressure at 2,000 rpm
(Elposition)
830 - 880 {8.5 - 9.0, 120 - 130} 780 (8.0, 110)
Throttle pressure B Throttle fully closed
Throtlle Iully opened
0 - 1 s { 0 - 0 . 1 5 , 0 - 2 1 )
830 - 880 (8.5 - 9.0, 120 - 130)
780 18.0, 110)
Stall speed rpm (Check with car on level ground)
2,200 - 2,600
Below 2,200,
above 2,600
3-9