Alcatel-Lucent 1850 TSS-320 User Provisioning Manual page 303

Procedures
............................................................................................................................................................................................................................................................
– LOCAL-REPAIR For future release
Layer: The combo-box allows to select the Layer type for the connection. It is related
•
to switching capability of the LSP tunnel. Possible values:
– MPLS
– PSC
– TDM
– DWDM
Source Address: The entry box allows to digit, in the {1-99, 101-126,128-223} - {0-
•
255} - {0-255} - {1-254} format, the Source Node IP Address as originating point of
the connection. This parameter is applied only for INNI connections.
Destination Address: The entry box allows to digit, in the {1-99, 101-126,128-223} -
•
{0-255} - {0-255} - {1-254} format, the Destination Node IP Address as target point
of the connection. This parameter is applied only for INNI connections.
Source Port ID: The entry box allows to digit, in the <rate>-<rack>-<shelf>-<slot>
•
format, the Service termination Port Access Identifier. It is located on the originating
node of the connection. Port AID can be an OC-n facility or a VCG termination type.
Destination Port ID: The entry box allows to digit, in the <rate>-<rack>-<shelf>-
•
<slot> format, the Service termination Port Access Identifier. It is located on the target
node of the connection. Port AID can be an OC-n facility or a VCG termination type.
Source Label: The entry box allows to digit a generalized Label value to be used at
•
connection source on ingress node port. Label format depends on the selected layer
type (MPLS/TDM). <five dash separated numeric string> (TDM label type) S#-U#-
K#-L#-M# format. Format label is defined only for TDM layer. Possible values:
– S#={0 - 65535} (Index of STS-3/AUG-1 within a STS-3xN multiplexed signal)
– U# = {0 - 15} (Index of STS-1-SPE/VC-3 within a STS-3/AUG-1 signal)
– K# = {0 - 15} (Index of TUG-3 within a VC-4 signal)
– L# = {0 - 15} (Index of VT-Group/TUG-2 within a STS-1-SPE/TUG-3 or VC-3
– M# = {0 - 15} (Index of VT1.5-SPE/VC11 or VT2-SPE/VC12 or VT3-SPE within
Destination Label: The entry box allows to digit a generalized Label value to be used
•
at connection destination on egress node port. Label format is defined only for SONET
layer (TDM label type) <five dash separated numeric string> (TDM label type) S#-
U#- K#-L#-M# format. Format label is defined only for TDM layer. Possible values:
– S#={0 - 65535} (Index of STS-3/AUG-1 within a STS-3xN multiplexed signal)
– U# = {0 - 15} (Index of STS-1-SPE/VC-3 within a STS-3/AUG-1 signal)
– K# = {0 - 15} (Index of TUG-3 within a VC-4 signal)
– L# = {0 - 15} (Index of VT-Group/TUG-2 within a STS-1-SPE/TUG-3 or VC-3
............................................................................................................................................................................................................................................................
8DG08136EAAA
Issue 3 July 2009
signal)
a VTGroup/TUG-2 signal)
signal)
Control Plane - Signalling: Create Network Connection
5 - 4 3