Fram Data - Sony HDCAM HDW-F900R Maintenance Manual

1-18. Contents of the EEPROM, NV-RAM and FRAM Data
The data that is stored in the EEPROM, NV-RAM and FRAM on the respective boards, is shown below.
n
Part numbers of the following ICs are shown in Vol. 2 Section "1. Spare Parts" of the separate Mainte-
nance Manual are the ICs before saving the data contents.
Board Ref.No.
(address)
DCP-43 IC611
(D-3/B side)
IC51
(A-2/B side)
DR-614 IC31
(D-2/B side)
IFA-19G IC202
(A-2/A side)
DC-110A IC15
(HKDW-702) (C-2/B side)
DC-139 IC206
(HKDW-902R) (B-2/B side)
MDC-13G IC403
(G-2/A side)
FP-152 IC816
(E-2/B side)
IC-819
(E-3/B side)
EQ-88G IC1104
(B-1/A side)
RP-131 IC19
(C-3/A side)
*1 : Users' unique data is saved in IC611 and IC51 of the DCP-43 board. When these ICs are replaced on the occasion of board
replacement or IC replacement, the users' unique data will be lost and the data is returned to the default data when the unit is
shipped from the factory. For the menu setting, refer to Section 4 and re-set the data. For the adjustment items that are required in
accordance with the replacement, refer to Section 1-17-7.
*2 : Because data cannot be set again, IC202 of the IFA-19G board cannot be exchanged.
When the IFA-19G board is replaced, remove IC202 from the former board and reinstall it to the new replacement IFA-19G board.
When IC202 needs to be replaced due to defective IC, contact your local Sony Sales Office/Service Center.
*3 : Data cannot be saved in IC816 on the FP-152 board.
When IC needs to be replaced due to defective IC, contact your local Sony Sales Office/Service Center.
*4 : Because data cannot be set again, IC31 of the DR-614 substrate cannot be exchanged.
When the DR-614 board is replaced, remove IC31 from the former board and reinstall it to the new replacement DR-614 board.
When IC31 needs to be replaced due to defective IC, contact your local Sony Sales Office/Service Center.
*5 : This function is enabled only when the DC-139 board (HKDW-902R) is installed.
1-54
EEPROM/ Contents of the saved data
NV-RAM/FRAM
EEPROM DCP board factory set value
Black Set adjustment value
FRAM All of the setup data of the setup menu
AWB/ABB data
EEPROM CCD block factory set value
Temperature measurement data
Mired value of filters
ND offset factory set value
EEPROM Model name, Serial No., OEM code
Model code, Device ID
EEPROM Level adjustment value of the respective
down-converter outputs
EEPROM
EEPROM Servo system adjustment value,
Hours meter
RAM inside CPU Hours meter
EEPROM Audio adjustment data
EEPROM RF system adjustment value
NV-RAM Unique data of CCD block
Adjustment/setup
upon replacement of
EEPROM/NV-RAM/FRAM
*1
*4
*2
9-29. SD VCO
Adjustment
9-30. SD Y Level
Adjustment
9-31. SD ZEBRA
Clamp Level
Adjustment
9-32. SD ZEBRA Y
Level
Adjustment
9-33. VF 2-3 Pull Down
HD Y Level
*5
Adjustment
Refer to Section 1-17-8.
*3
10-2-1.Audio A/D Error
Adjustment
10-2-2.Audio D/A Error
Adjustment
10-2-3.AUDIO LEVEL
Volume Control
(Inside Panel)
Adjustment
Refer to Section
1-17-11.
Refer to Section
1-17-4.
HDW-F900R/V1 (E)