KYOWA WGA-910A Series Instruction Manual page 3

6-2-2. Zero Compensation ········································································································ 57
6-2-3. Additional Value ············································································································ 58
6-2-4. Sensor Output Value (Original Value) ················································································· 59
6-3. MEAS. COND. SETTING (SETTING MEASURING CONDITION) ··············································· 60
6-3-1. Measuring Condition ······································································································ 60
6-3-2. Comparison Setting ········································································································ 61
6-3-3. Measure Mode Setting····································································································· 65
6-3-4. Descriptions of the operation mode····················································································· 70
6-3-5. How WGA-910A works with HOLD and RESET commands ···················································· 77
6-3-6. Relations Between Control Inputs, Comparator Outputs, and Operation Statuses for [Block Peak-
Bottom] and [Time Peak-Bottom] ······················································································ 78
6-4. WAVE DISPLAY SETTING (SETTING WAVEFORM DISPLAY) ·················································· 79
6-4-1. Setting X-axis················································································································ 79
6-4-2. Setting Y-axis ················································································································ 81
6-4-3. Start Mode of Wave (Trigger Mode) ··················································································· 82
6-4-4. Passed Level (Trigger Level) ····························································································· 83
6-4-5. Level Passed Way (Trigger Slope)······················································································· 84
6-4-6. Hold Time of Wave ········································································································· 84
6-5. INITIAL SETTING ············································································································· 85
6-5-1. Meas. Select Signal (Measuring Condition Selecting Signal)······················································ 85
6-5-2. System························································································································· 86
6-5-3. Self-Check···················································································································· 90
6-5-4. Operation Check············································································································ 92
6-5-5. SD CARD SETTING ······································································································ 98
7. OPERATION TIMING ·············································································································108
7-1. CONTROL INPUT (HOLD COMMAND, RESET COMMAND, ZERO COMMAND) ·······················108
7-1-1. Control Input···············································································································108
7-1-2. Block-specified ·············································································································109
7-1-3. Time-specified ··············································································································109
7-2. COMPARATOR OUTPUT ···································································································110
7-3. DELAY TIME BETWEEN INPUT AND OUTPUT·····································································110
7-4. DISPLAYING WAVEFORMS AND OUTPUTTING SD SIGNAL WITH WAVEFORM COMMAND
(CONTROL OUTPUT) AND RECORD KEY ············································································111
7-4-1. Single Mode·················································································································111
7-4-2. Auto Mode, Normal Mode ·······························································································112
8. RS-232C COMMUNICATION ····································································································114
8-1. RS-232C INTERFACE ········································································································114
8-2. CONTROL COMMAND······································································································114
8-3. DETAILS OF CONTROL COMMANDS ·················································································116
8-3-1. Initial setting················································································································116
8-3-2. Reading ······················································································································118
8-3-3. Executing····················································································································120
8-3-4. Setting························································································································122
8-3-5. Other ·························································································································130
8-4. OPERATION AND FUNCTION OF THE COM. SETTING (COMMUNICATION SETTING)·············131
9. TROUBLESHOOTING·············································································································133
9-1. POWER SWITCH CANNOT TURN ON THE WGA-910A ··························································133
9-2. DISPLAYING ERRORS ······································································································133
9-3. DISPLAY VALUE OR MONITOR OUTPUT DOES NOT CHANGE ··············································135
9-4. ZERO POINT IS UNSTABLE ·······························································································135
9-5. OPERATION STOPS AND ACCEPTS NO INSTRUCTION AT ALL.·············································135
9-6. LARGE NOISE ·················································································································136
10. MAINTENANCE ···················································································································137