Danfoss VLT AQUA Drive FC 200 Programming Manual page 105

Parameter Description
13-40 Logic Rule Boolean 1
Array [6]
Option: Function:
[6] Current Limit See parameter group 5-3* for further
description.
[7] Out of current See parameter group 5-3* for further
range description.
[8] Below I low See parameter group 5-3* for further
description.
[9] Above I high See parameter group 5-3* for further
description.
[10] Out of speed range
[11] Below speed low See parameter group 5-3* for further
description.
[12] Above speed high See parameter group 5-3* for further
description.
[13] Out of feedb. See parameter group 5-3* for further
range description.
[14] Below feedb. low See parameter group 5-3* for further
description.
[15] Above feedb. high See parameter group 5-3* for further
description.
[16] Thermal warning See parameter group 5-3* for further
description.
[17] Mains out of range See parameter group 5-3* for further
description.
[18] Reverse See parameter group 5-3* for further
description.
[19] Warning See parameter group 5-3* for further
description.
[20] Alarm (trip) See parameter group 5-3* for further
description.
[21] Alarm (trip lock) See parameter group 5-3* for further
description.
[22] Comparator 0 Use the result of comparator 0 in the
logic rule.
[23] Comparator 1 Use the result of comparator 1 in the
logic rule.
[24] Comparator 2 Use the result of comparator 2 in the
logic rule.
[25] Comparator 3 Use the result of comparator 3 in the
logic rule.
[26] Logic rule 0 Use the result of logic rule 0 in the
logic rule.
[27] Logic rule 1 Use the result of logic rule 1 in the
logic rule.
®
VLT AQUA Drive Programming Guide
13-40 Logic Rule Boolean 1
Array [6]
Option:
[28]
[29]
[30]
[31]
[32]
[33]
[34]
[35]
[36]
[37]
[38]
[39]
[40]
[41]
[42]
[43]
[44]
®
MG20O622 - VLT is a registered Danfoss trademark
Function:
Logic rule 2 Use the result of logic rule 2 in the
logic rule.
Logic rule 3 Use the result of logic rule 3 in the
logic rule.
SL Timeout 0 Use the result of timer 0 in the logic
rule.
SL Timeout 1 Use the result of timer 1 in the logic
rule.
SL Timeout 2 Use the result of timer 2 in the logic
rule.
Digital input DI18 Use the value of DI18 in the logic rule
(High = TRUE).
Digital input DI19 Use the value of DI19 in the logic rule
(High = TRUE).
Digital input DI27 Use the value of DI27 in the logic rule
(High = TRUE).
Digital input DI29 Use the value of DI29 in the logic rule
(High = TRUE).
Digital input DI32 Use the value of DI32 in the logic rule
(High = TRUE).
Digital input DI33 Use the value of DI33 in the logic rule
(High = TRUE).
Start command This logic rule is TRUE if the
adjustable frequency drive is started
by any means (either via digital input,
serial communication bus or other).
Drive stopped This logic rule is TRUE if the
adjustable frequency drive is stopped
or coasted by any means (either via
digital input, serial communication
bus or other).
Reset Trip This logic rule is TRUE if the
adjustable frequency drive is tripped
(but not trip-locked) and [Reset] is
pressed.
Auto Reset Trip This logic rule is TRUE if the
adjustable frequency drive is tripped
(but not trip-locked) and an
automatic reset is issued.
OK key This logic rule is TRUE if the OK key
on the LCP is pressed.
Reset Key This logic rule is TRUE if the Reset key
on the LCP is pressed.
3 3
3-79