Danfoss VLT AQUA Drive FC 200 Programming Manual page 101

Parameter Description
13-02 Stop Event
Option: Function:
[3] In range See parameter group 5-3* for further
description.
[4] On reference See parameter group 5-3* for further
description.
[5] Torque limit See parameter group 5-3* for further
description.
[6] Current Limit See parameter group 5-3* for further
description.
[7] Out of current See parameter group 5-3* for further
range description.
[8] Below I low See parameter group 5-3* for further
description.
[9] Above I high See parameter group 5-3* for further
description.
[10] Out of speed range
[11] Below speed low See parameter group 5-3* for further
description.
[12] Above speed high See parameter group 5-3* for further
description.
[13] Out of feedb. range See parameter group 5-3* for further
description.
[14] Below feedb. low See parameter group 5-3* for further
description.
[15] Above feedb. high See parameter group 5-3* for further
description.
[16] Thermal warning See parameter group 5-3* for further
description.
[17] Mains out of range See parameter group 5-3* for further
description.
[18] Reverse See parameter group 5-3* for further
description.
[19] Warning See parameter group 5-3* for further
description.
[20] Alarm (trip) See parameter group 5-3* for further
description.
[21] Alarm (trip lock) See parameter group 5-3* for further
description.
[22] Comparator 0 Use the result of comparator 0 in the
logic rule.
[23] Comparator 1 Use the result of comparator 1 in the
logic rule.
[24] Comparator 2 Use the result of comparator 2 in the
logic rule.
®
VLT AQUA Drive Programming Guide
13-02 Stop Event
Option:
[25]
[26]
[27]
[28]
[29]
[30]
[31]
[32]
[33]
[34]
[35]
[36]
[37]
[38]
[39]
[40]
[41]
[42]
[43]
®
MG20O622 - VLT is a registered Danfoss trademark
Function:
Comparator 3 Use the result of comparator 3 in the
logic rule.
Logic rule 0 Use the result of logic rule 0 in the
logic rule.
Logic rule 1 Use the result of logic rule 1 in the
logic rule.
Logic rule 2 Use the result of logic rule 2 in the
logic rule.
Logic rule 3 Use the result of logic rule 3 in the
logic rule.
SL Timeout 0 Use the result of timer 0 in the logic
rule.
SL Timeout 1 Use the result of timer 1 in the logic
rule.
SL Timeout 2 Use the result of timer 2 in the logic
rule.
Digital input DI18 Use the value of DI18 in the logic
rule (High = TRUE).
Digital input DI19 Use the value of DI19 in the logic
rule (High = TRUE).
Digital input DI27 Use the value of DI27 in the logic
rule (High = TRUE).
Digital input DI29 Use the value of DI29 in the logic
rule (High = TRUE).
Digital input DI32 Use the value of DI32 in the logic
rule (High = TRUE).
Digital input DI33 Use the value of DI33 in the logic
rule (High = TRUE).
Start command This event is TRUE if the adjustable
frequency drive is started by any
means (either via digital input, serial
communication bus or other).
Drive stopped This event is TRUE if the adjustable
frequency drive is stopped or coasted
by any means (either via digital input,
serial communication bus or other).
Reset Trip This event is TRUE if the adjustable
frequency drive is tripped (but not
trip-locked) and [Reset] is pressed.
Auto Reset Trip This event is TRUE if the adjustable
frequency drive is tripped (but not
trip-locked) and an automatic reset is
issued.
OK key This event is TRUE if [OK] is pressed.
3 3
3-75