Specifications - Jeep J-10 Series 1982 Technical & Service Manual

2C-66 AUTOMATIC TRANSMISSION
SPRING
SEAL RINGS
90541
Fig. 2C-99 Accumulator Assembly
(4) Insert park lock rod through opening in rear of
case.
(5) Position knob of lock rod against reaction plug
and sprag.
(6) Move front end of rod toward centerline of
transmission while exerting rearward pressure on rod to
force it past sprag. Rotate output shaft, if necessary.
NOTE: Before installing the valve body, be sure the
neutral start switch has not yet been installed.
(7) Place valve body manual lever in Drive position.
(8) Place valve body assembly in its approximate
position in case.
(9) Align valve body in case and install attaching
screws finger-tight.
(10) Install neutral start switch.
(11) Shift valve body manual lever to Neutral
position.
(12) Relocate valve body if necessary to align manual
lever neutral finger over neutral start switch plunger
ball.
(13) Tighten valve body attaching screws to 100 inch-
pounds (11 N*m) torque.
(14) Install gearshift control lever on manual lever
shaft and tighten clamp bolt.
(15) Check lever shaft for binding in case by moving
lever through all detent positions.
NOTE: If binding exists, loosen the valve body attach
ing screws and align the valve body.
(16) Install flat washer and throttle lever and tighten
throttle lever clamp bolt.
Rear Band Adjustment
(1) Loosen locknut and back nut off five turns.
(2) Tighten band adjusting screw to 72 inch-pounds
(8 N#m) torque.
CAUTION: If Adapter Tool J-24063 is used to adjust
the band, tighten the adjusting screw to 36 inch-pounds
(4 N*m) torque only.
(3) Back off adjusting screw four turns on 999 and
two turns on 727.
(4) Hold adjusting screw in position and tighten
locknut to 35 foot-pounds (47 N»m) torque.
(5) Install oil pan and gasket.
Front Band Adjustment
(1) Loosen locknut and back nut off five turns.
(2) Be sure band adjusting screw turns freely in
case. Lubricate screw, if necessary.
(3) Tighten band adjusting screw to 72 inch-pounds
(8 N»m) torque using Torque Wrench J-5853 and a 5/16
(8 mm) square socket.
CAUTION: If Adapter Tool J-24063 is used to adjust
the band, tighten the adjusting screw to 36 inch-pounds
(4 N*m) torque only.
(4) Back off adjusting screw two turns on 999 and
two and one-half turns on 727.
(5) Hold adjusting screw in position and tighten
locknut to 35 foot-pounds (47 N*m) torque.
SPECIFICATIONS
Clutch Plate Clearance
Front Clutch
Transmission Specifications
MODEL 999
3 Disc 0.074 to 0.125 inch
4 Disc 0.067 to 0.134 inch
5 Disc 0.075 to 0.152 inch
3 and 4 Disc 0.032 to 0.55 inch Rear Clutch
Clutch Component Thickness Tolerance
Front Clutch
Lined Plate
Steel Plate
Pressure Plate
Rear Clutch
Lined Plate
Steel Plate
Flat Pressure Plate
Formed Pressure Plate
Clutches
Number of Front Clutch Plates
Number of Front Clutch Discs
Number of Rear Clutch Plates
Number of Rear Clutch Discs
0.083 to 0.088 inch
0.066 to 0.071 inch
0.244 to 0.218 inch
0.060 to 0.065 inch
0.066 to 0.071 inch
0.214 to 0.218 inch
0.409 to 0.413 inch
5
5
3
4
MODEL 727
3 Disc 0.070 to 0.129 inch
4 Disc 0.082 to 0.051 inch
4 Disc 0.025 to 0.045 inch
0.090 to 0.095 inch
0.066 to 0.071 inch
0.278 to 0.282 inch
0.060 to 0.065 inch
0.066 to 0.071 inch
0.278 to 0.282 inch
0.441 to 0.445 inch
4
4
3
4
70122A