Outside Mirrors - Jeep J-10 Series 1982 Technical & Service Manual

3J-10 DOORS
outside screws, then install and tighten inner screw on
each hinge. Tighten screws to 25 to 35 foot-pounds (34 to
47 N*m) torque.
(13) Remove door holding fixture.
(14) Position electrical harnesses inside door.
(15) Check door alignment. Adjust if necessary (refer
to Door Adjustment).
(16) Connect electrical harnesses.
(17) Install water shield and trim panel.
Door Adjustments
The doors are adjusted at the hinge mounting points
on the body or door.
The slotted center hole is provided in the hinge for in
or out adjustment on the pillars. The upper and lower
holes in the hinge set the door outboard slightly. To
adjust the door inboard, loosen the center screw and
push the door open against door stop. Tighten the center
screw after correct alignment has been achieved.
To adjust up or down or fore and aft, loosen the hinge
attaching screws in the door and move the door to the
desired position and tighten the screws.
Prior to any door adjustment or alignment, the ad
justable striker must be removed to allow the door to
close freely in proper alignment without striker
interference.
The door lock striker is adjustable up, down, in or out
and can be shimmed forward or back to hold the door in
the properly aligned position.
The door latch striker should be set so that the latch
enters the striker without binding, yet provides secure
retention for the lock and prevents up and down or in
and out movement of the door.
The striker should also be adjusted in or out to allow
the door latch to be fully engaged. The door should be
flush with the adjacent body panels.
NOTE: It is possible to set the striker in so far that the
door is closed tight but only the safety catch is engaged.
This prevents locking the door with the pushbutton lock
rod.
OUTSIDE MIRRORS
Standard Mirror
Removal
(1) Remove screws attaching mirror to door panel.
(2) Remove mirror and gasket from door panel.
Installation
(1) Position gasket and mirroron door panel.
(2) Installscrews attachingmirrorto door panel.
Remote Control Mirrors
Removal
(1) Remove door trim panel. ?• • '
(2) Remove setscrew attaching mirror remote con
trol assembly to trim panel escutcheon.
(3) Remove water shield paper.
(4) Remove screws attaching remote mirror-to-door
panel using Torx Bit Tool J-25359-C.
NOTE: Check and note routing of remote mirror con
trol cables before removing assembly from door panel
(5) Remove remote mirror and gasket from door
panel.
Installation
(1) Assemble remote mirror and gasket.
(2) Insert remote mirror control cables into door
outer panel and duplicate routing of control cables into
door inner panel as previously noted during removal.
(3) Install screws attaching remote mirror-to-door
panel using Torx Bit Tool J-25359-C.
(4) Install setscrew attaching mirror remote control
assembly to trim panel escutcheon.
(5) Check mirror operation.
(6) Install water shield paper.
(7) Install door trim panels.
Electric Remote Control Mirrors
Electric remote control mirrors are available on Cher
okee—Wagoneer models equipped with power windows.
Both mirrors are controlled by a dual function switch
located on the left front door panel. The left/right con
trol switch is used for directing current to the desired
mirror. The horizontal/vertical switch directs current to
the motor in the mirror assembly which moves the mir
ror as desired. A safety or overrun feature is designed
into the mirror to prevent damage to the motor when
the mirror is moved by hand or when running the mirror
to the maximum limit. When the mirror is moved by
hand or run to the maximum limit, a distinct snapping
noise can be heard.
Electric Motor/Switch Test
Before conducting the electric motor/switch test, be
sure the battery is fully charged and all connections are
clean and tight.
(1) Check accessory fuse.
(2) Check for good ground wire (black) connection
located at base of fuse panel.
(3) Remove door trim panel.
(4) Using test light, check for current as follows:
(a) Orange input wire to switch—if no current
is present, check for broken ground (black) wire or feed