Table of Contents
Advertisement
03–48
Transmission case oil seal drive in depth
Transmission clutch hub No.2 snap ring thickness
Input shaft rear radial ball bearing snap ring clearance
Input shaft rear radial ball bearing snap ring thickness
3rd gear radial clearance
4th gear radial clearance
3rd gear thrust clearance
4th gear thrust clearance
Output shaft assy
1st gear thrust clearance
2nd gear thrust clearance
1st gear radial clearance
2nd gear radial clearance
Output shaft run out
Output shaft standard outer diameter
Output shaft minimum outer diameter
2nd gear inside diameter
1st gear inside diameter
Between the 2nd gear while and synchronizer ring No.2 back clearance
Between the 1st gear while and synchronizer ring set No.1 back clearance
Reverse gear groove – thickness of the claw part on gear shift fork No.1
clearance
2nd gear radial clearance
1st gear radial clearance
2nd gear thrust clearance
1st gear thrust clearance
Differential case assy
Front differential side gear backlash
Front differential pinion thrust washer thickness
Front differential pinion shaft No.1 thickness
Front differential side gear backlash
2002 CAMRY REPAIR MANUAL (RM881U)
SERVICE SPECIFICATIONS
Standard clearance 0.1 mm or less (0.0039 in. or less)
KOYO made
NSK made
KOYO made
NSK made
Standard clearance 0.10 – 0.35 mm (0.0039 – 0.0138 in.)
Standard clearance 0.10 – 0.57 mm (0.0039– 0.0224 in.)
Standard clearance 0.25 – 0.40 mm (0.0098 – 0.0157 in.)
Standard clearance 0.10 – 0.35 mm (0.0039 – 0.0138 in.)
KOYO made
NSK made
KOYO made
NSK made
Maximum run out 0.03 mm (0.0012 in.)
Standard inside diameter
Maximum inside diameter
Standard inside diameter
Maximum inside diameter
Standard clearance
KOYO made
NSK made
KOYO made
NSK made
Standard clearance 0.10 – 0.35 mm (0.0039 – 0.0138 in.)
Standard clearance 0.25 – 0.40 mm (0.0098 – 0.0157 in.)
Standard backlash 0.05 – 0.20 mm (0.0020 – 0.0079 in.)
Minimum thickness 0.9 mm (0.035 in.)
Minimum thickness 17.975 mm (0.70768 in.)
Standard backlash 0.05 – 0.20 mm (0.0020 – 0.0079 in.)
–
MANUAL TRANSMISSION / TRANSAXLE
3.5 " 0.5 mm (0.138 " 0.020 in.)
H
2.30 – 2.35 mm (0.0906 – 0.0925 in.)
J
2.35 – 2.40 mm (0.0925 – 0.0945 in.)
K
2.40 – 2.45 mm (0.0945 – 0.0965 in.)
L
2.45 – 2.50 mm (0.0965 – 0.0984 in.)
M
2.50 – 2.55 mm (0.0984 – 0.1004 in.)
N
2.55 – 2.60 mm (0.1004 – 0.1024 in.)
P
2.60 – 2.65 mm (0.1024 – 0.1043 in.)
1
2.35 – 2.40 mm (0.0925 – 0.0945 in.)
2
2.40 – 2.45 mm (0.0945 – 0.0965 in.)
3
2.45 – 2.50 mm (0.0965 – 0.0984 in.)
4
2.50 – 2.55 mm (0.0984 – 0.1004 in.)
5
2.55 – 2.60 mm (0.1004 – 0.1024 in.)
6
2.60 – 2.65 mm (0.1024 – 0.1043 in.)
7
2.65 – 2.70 mm (0.1043 – 0.1063 in.)
8
2.70 – 2.75 mm (0.1063 – 0.1083 in.)
0.009 – 0.053 mm (0.0004 – 0.0021 in.)
0.009 – 0.051 mm (0.0004 – 0.0020 in.)
0.009 – 0.053 mm (0.0004 – 0.0021 in.)
0.009 – 0.051 mm (0.0004 – 0.0020 in.)
0.009 – 0.053 mm (0.0004 – 0.0021 in.)
0.009 – 0.051 mm (0.0004 – 0.0020 in.)
0.009 – 0.053 mm (0.0004 – 0.0021 in.)
0.009 – 0.051 mm (0.0004 – 0.0020 in.)
A
37.610 – 37.626 mm (1.4807 – 1.4813 in.)
B
34.802 – 34.512 mm (1.3702 – 1.3587 in.)
A
37.610 mm (1.4807 in.)
B
34.802 mm (1.3702 in.)
50.009 – 50.025 mm (1.9689 – 1.9695 in.)
50.025 mm (1.9695 in.)
51.009 – 51.025 (2.0082 – 2.0089 in.)
51.025 mm (2.0089 in.)
0.70 – 1.45 mm (0.0276 – 0.0571 in.)
0.70 – 1.45 mm (0.0276 – 0.0571 in.)
0.15 – 0.35 mm (0.0059 – 0.0138 in.)
0.009 – 0.053 mm (0.0004 – 0.0021 in.)
0.009 – 0.051 mm (0.0004 – 0.0020 in.)
0.009 – 0.053 mm (0.0004 – 0.0021 in.)
0.009 – 0.051 mm (0.0004 – 0.0020 in.)
Author :
Date :
159
Advertisement
Table of Contents
