Table of Contents
Advertisement
Transmission case oil seal drive in depth
Front differential case shim RR thickness
Front differential case oil seal clearance
Input shaft front bearing clearance
Reverse restrict pin clearance
Transmission clutch hub No.3 snap ring clearance
Transmission clutch hub No.3 snap ring thickness
5th gear radial clearance
5th gear thrust clearance
Input shaft assy
4th gear thrust clearance
3rd gear thrust clearance
4th gear radial clearance
3rd gear radial clearance
Input shaft run out
Input shaft standard outer diameter
Input shaft minimum outer diameter
4th gear inside diameter
3rd gear inside diameter
Between the 4th gear spline end and synchronizer outer ring back clearance
Between the 3rd gear spline end and synchronizer outer ring back clearance
Transmission hub sleeve No.3 groove – thickness of the claw part on gear
shift fork No.1
Transmission clutch hub No.2 snap ring clearance
2002 CAMRY REPAIR MANUAL (RM881U)
SERVICE SPECIFICATIONS
Standard clearance 0.009 – 0.050 mm (0.0004 – 0.0020 in.)
Standard clearance 0.10 – 0.65 mm (0.0039 – 0.0260 in.)
Standard clearance 0.10 – 0.57 mm (0.0039– 0.0224 in.)
Standard clearance 0.10 – 0.35 mm (0.0039 – 0.0138 in.)
KOYO made
NSK made
KOYO made
NSK made
Maximum run out: 0.03 mm (0.0012 in.)
Standard inside diameter
Maximum inside diameter
Standard inside diameter
Maximum inside diameter
Standard clearance
Standard clearance 0.1 mm or less (0.0039 in. or less)
–
MANUAL TRANSMISSION / TRANSAXLE
3.5 " 0.5 mm (0.138 " 0.020 in.)
0
2.00 mm (0.0787 in.)
1
2.05 mm (0.0807 in.)
2
2.10 mm (0.0827 in.)
3
2.15 mm (0.0846 in.)
4
2.20 mm (0.0866 in.)
5
2.25 mm (0.0886 in.)
6
2.30 mm (0.0906 in.)
7
2.35 mm (0.0925 in.)
8
2.40 mm (0.0945 in.)
9
2.45 mm (0.0965 in.)
A
2.50 mm (0.0984 in.)
B
2.55 mm (0.1004 in.)
C
2.60 mm (0.1024 in.)
D
2.65 mm (0.1043 in.)
E
2.70 mm (0.1063 in.)
F
2.75 mm (0.1083 in. )
G
2.80 mm (0.1102 in.)
H
2.85 mm (0.1122 in.)
1 – 2 mm (0.0394 –0.0787 in.)
4.28 – 4.60 mm (0.1685 – 0.1811 in.)
12.5 – 13.5 mm (0.492 – 0.531 in.)
0.1 mm or less (0.0039 in. or less)
a
1.75 – 1.80 mm (0.0689 – 0.0709 in.)
b
1.80 – 1.85 mm (0.0709 – 0.0728 in.)
c
1.85 – 1.90 mm (0.0728 – 0.0748 in.)
d
1.90 – 1.95 mm (0.0748 – 0.0768 in.)
e
1.95 – 2.00 mm (0.0768 – 0.0787 in.)
f
2.00 – 2.05 mm (0.0787 – 0.0807 in.)
g
2.05 – 2.10 mm (0.0807 – 0.0827 in.)
h
2.10 – 2.15 mm (0.0827 – 0.0846 in.)
j
2.15 – 2.20 mm (0.0846 – 0.0866 in.)
0.009 – 0.053 mm (0.0004 – 0.0021 in.)
0.009 – 0.051 mm (0.0004 – 0.0020 in.)
0.009 – 0.053 mm (0.0004 – 0.0021 in.)
0.009 – 0.051 mm (0.0004 – 0.0020 in.)
A
35.984 – 36.000 mm (1.4167 – 1.4173 in.)
B
35.984 – 36.000 mm (1.4167 – 1.4173 in.)
C
27.957 – 27.972 mm (1.1007 – 1.1013 in.)
A
35.984 mm (1.4167 in.)
B
35.984 mm (1.4167 in.)
C
27.957 mm (1.1007 in.)
42.09 – 42.025 mm (1.6539 – 1.6545 in.)
42.025 mm (1.6545 in.)
43.009 – 43.025 mm (1.6933 – 1.6939 in.)
43.025 mm (1.6939 in.)
0.75 – 1.65 mm (0.0295 – 0.0650 in.)
0.65 – 1.75 mm (0.0256 – 0.0689 in.)
0.15 – 0.35 mm (0.0059 – 0.0138 in.)
Author :
03–47
Date :
158
Advertisement
Table of Contents
