Thermo Scientific APEX 100 User Manual page 421

4
D
C
50 1.97
155 6.09 A (APERTURE WIDTH)
A + 230[9.06]
4X 32 1.26 4X M10X1.5
B
CABLE
PORT
A + 100[3.94]
A
SEE SHEET 1 FOR REVISION INFORMATION
REV ECO
4
3
75 2.95
100 [3.94] FOR B=50 ONLY
EPOXY LINED
B
APERTURE
(APERTURE HEIGHT)
75 2.95
50 1.97
75 2.95
12[.47]
(E)
(HEAD WIDTH)
2X D
2X E
2X 25 .98
DESCRIPTION
3
B (APERTURE
HEIGHT, mm)
100 150 200
50 145 145 145
75 145 145 145
100 145 145
125 145 145
150 145 OR 250 145 OR 250 145 OR 250 145 OR 250 145 OR 250 145 OR 250 145 OR 250 145 OR 250
175 145 OR 250 145 OR 250 145 OR 250 145 OR 250 145 OR 250 145 OR 250 145 OR 250 145 OR 250
200
225
250
4X 12 .47
75[2.95]
C
145[5.71]
OR
250[9.84]
TOLERANCE UNLESS SPECIFIED:
ALL DIMENSIONS ARE IN MILLIMETERS AND [INCHES]
X
X.X
75[2.95]
X.XX
ANGLES
REMOVE ALL BURRS & UNNECESSARY
SHARP EDGES
This document is confidential and is the property of Thermo Fisher
Scientific ("Thermo"). It may not be copied or reproduced in any
manner without the expressed written consent of Thermo. This
document also is an unpublished work of Thermo. Thermo intends to
and is maintaining the work as confidential information. Thermo also
may seek to protect this work as an unpublished copyright. In the
event of either inadvertent or deliberate publication, Thermo
intends to enforce it's rights to this work under the copyright laws as
a published work. Those having access to this work may not copy,
use or disclose the information in this work unless expressly
authorized by Thermo.
BY APP DATE
2
RECTANGULAR APERTURE HEADS: C (HEAD WIDTH, mm)
A (APERTURE WIDTH, mm)
250 300 350 400
145 145 145 145
145 145 145 145
145 145 145 145
145 145 145 145
145 OR 250 145 OR 250 145 OR 250 145 OR 250 145 OR 250 145 OR 250 145 OR 250
145 OR 250 145 OR 250 145 OR 250 145 OR 250 145 OR 250 145 OR 250 145 OR 250
145 OR 250 145 OR 250 145 OR 250 145 OR 250 145 OR 250 145 OR 250
mm[INCH]
145[5.71]
250[9.84]
AUDIT CHECK
(OPTIONAL)
HORIZONTAL APERTURE
HORIZONTAL PRODUCT FLOW
ENGINEER: DATE:
DMG 5/31/07
DATE:
DRAWN BY:
5/31/07
DMG
DATE:
CHECKED BY:
5/31/07
DMG
APEX 300 OUTLINE AND MOUNTING
PART NUMBER:
810108
DRAWING NUMBER
SCALE
SIZE
1:3 B
PROJECTION
Derived From:
2
1
450 500 550
145 145 145
D
145 145 145
145 145 145
145 145 145
SQUARE APERTURE HEADS
A & B (mm) C (mm)
75 145 OR 250
100 145 OR 250
125 145 OR 250
150 145 OR 250
175 145 OR 250
C
200 145 OR 250
225 145 OR 250
250 145 OR 250
275 250
300 250
325 250
350 250
FOOT DIMENSION TABLE
C D E
mm[INCH] mm[INCH]
100[3.94] 22.5[.89]
200[7.87] 25[.98]
B
A
REV SHEET
07387M-B300
B
2 of 5
© 2007, by Thermo Fisher Scientific
1