Parameter Default Values For Different Macros - ABB ACS580 Firmware Manual

80 Control macros

Parameter default values for different macros

Chapter Parameters
ABB standard macro (factory macro). Some parameters have different default values
for other macros. The tables below lists the default values for those parameter for
each macro.
96.04 Macro select
10.24 RO1 source
10.27 RO2 source
10.30 RO3 source
12.20 AI1 scaled at AI1
max
13.12 AO1 source
13.18 AO1 source max
19.11 Ext1/Ext2
selection
20.01 Ext1 commands
20.03 Ext1 in1 source
20.04 Ext1 in2 source
20.05 Ext1 in3 source
20.06 Ext2 commands
20.08 Ext2 in1 source
20.09 Ext2 in2 source
20.12 Run enable 1
source
22.11 Ext1 speed ref1
22.18 Ext2 speed ref1
22.22 Constant speed
sel1
22.23 Constant speed
sel2
on page 135 shows the default values of all parameters for the
1 = 17 =
ABB standard ABB stan-
dard (vector)
2 = Ready run 2 = Ready run
7 = Running 7 = Running
15 = Fault (-1) 15 = Fault (-1)
50.0 1500.0
2 = Output 1 = Motor
frequency speed used
50.0 1500.0
0 = EXT1 0 = EXT1
2 = In1 Start; 2 = In1 Start;
In2 Dir In2 Dir
2 = DI1 2 = DI1
3 = DI2 0 = Not
selected
0 = Not 0 = Not
selected selected
0 = Not 0 = Not
selected selected
0 = Not 0 = Not
selected selected
0 = Not 0 = Not
selected selected
1 = Selected 1 = Selected
1 = AI1 scaled 1 = AI1 scaled
0 = Zero 0 = Zero
4 = DI3 4 = DI3
5 = DI4 5 = DI4
11 = 12 =
3-wire Alternate
2 = Ready run 2 = Ready run
7 = Running 7 = Running
15 = Fault (-1) 15 = Fault (-1)
50.0 50.0
2 = Output 2 = Output
frequency frequency
50.0 50.0
0 = EXT1 0 = EXT1
5 = In1P Start; 3 = In1 Start
In2 Stop; In3 fwd; In2 Start
2 = DI1 2 = DI1
3 = DI2 3 = DI2
4 = DI3 0 = Not
selected
0 = Not 0 = Not
selected selected
0 = Not 0 = Not
selected selected
0 = Not 0 = Not
selected selected
1 = Selected 7 = DI6
1 = AI1 scaled 1 = AI1 scaled
0 = Zero 0 = Zero
5 = DI4 4 = DI3
6 = DI5 5 = DI4
13 =
Motor potenti-
ometer
2 = Ready run
7 = Running
15 = Fault (-1)
50.0
2 = Output
frequency
50.0
0 = EXT1
2 = In1 Start;
In2 Dir
2 = DI1
3 = DI2
0 = Not
selected
0 = Not
selected
0 = Not
selected
0 = Not
selected
7 = DI6
15 = Motor
potentiometer
0 = Zero
6 = DI5
0 = Not
selected