User Administrator Mode - Canon imagePRESS C1 P Service Manual

Chapter 1

1.2.3.10 User Administrator Mode

imagePRESS C1 P / imagePRESS C1
This part outlines the user administrator mode.
User administrator mode provides the adjustment function to User Administrator, who is superior to general user, and the function is classified mainly into 2 settings.
1. Device Management Setting
This setting enables to adjust color characteristics such as gradation, toner density, color and image quality, to realize an optimal image even under the influence
of every variation factor such as environmental change and aged deterioration.
This setting can be found in the following menu tree of the panel setting display:
- Initial Setup/Save Key > System Control Settings > Device Management Settings
Panel Item
Display
Default Auto Gradation
Display Adjustment
Default Shading
Display Correction
Default Dither Pattern
Display Setting (to
Switch Dither)
Displayed by Color Balance
Service
Switch (*1)
Displayed by Exposure
Service Recalibration
Switch (*1) when Scanning
Displayed by Density
Service Adjustment
Switch (*1) Mode
Displayed by Refresh the
Service Fixing Roller
Switch (*1)
Displayed by Fixing Roller
Service Auto Refresh
Switch (*1) Level
Displayed by Color Cast
Service Correction
Switch (*1)
Displayed by Tail End Color
Service Fading/
Switch (*1) Graininess
Correction
Displayed by White Gap
Service Correction
Switch (*1)
Displayed by 2-sided Print
Service Image Uneven
Switch (*1) Gloss Correction
Displayed by Tail End White
Service Patch Correction
Switch (*1)
*1:
This item is displayed by executing service mode (COPIER > OPTION > BODY > IMAG-ADJ)
1-18
Setting Objective
Full Adjust./Quick Adjust./ In a copy/ print job without special settings, adjust
Auto Gradation Adjust gradation, density or hue to reproduce the original image.
Method
Correction with Improve minor shading typically appeared in the halftone
Densitometer/ Visual area of a printed image.
Correction/ Correction by
Print server
Gradation (For Printer)/ Select a dither pattern. Dither means a technique to
Resolution (For Printer)/ express colors/gradation by small dots. The source data for
Reproduction of Scan Image: a dotted image is called 'dither pattern'. By changing this,
Newspaper/ Gradation/ High expression of a printed image can be modified.
gradation/ Color tone/ High
resolution/ Reproduction of
Scan Image
Fine-adjustment of toner Adjust the color balance or fine-adjust the default density
density each for Yellow, for Yellow, Magenta, Cyan and Black.
Magenta, Cyan and Black: -
8~0*~+8 (by 1)
Left edge: 0~5 (*0)Right
edge: 0~5 (*0)
A/B Modes (refer to *3) Switch the methods to control toner density.
Start key Slightly glossy lines in parallel of the feed direction
sometimes appear on the both ends of wider-width paper
after copying/ printing over hundreds sheets of narrower-
width paper (ex: using A3 after A4R). Specifically in the
high-density area on heavy/coated paper, cloudlike glossy
shading appears occasionally. Refreshing the fixing roller
and/or wiping the surface of the roller can improve these
symptoms.
Level: -5 to +5 (5*) The fixing roller is automatically refreshed after a certain
copies are printed. This mode provides adjustment in
refreshing frequency and time level for refreshing
operation.
Yellow, Magenta, Cyan, When 'color cast' is seen in blank area, this can be
Black: -2 to +2 (0*) corrected by color with this function.
ON/OFF* This is to improve color fading at the tail end/ white grains,
which can be appeared on halftone images.
1 to 4 (3*) If the dark colored area follows right after the halftone
area, 'white gap' can be appeared near the border in the
halftone area. This can be improved with this function.
ON/OFF* Gloss can be uneven on the first side when 2-sided printing
is performed on the coated paper (high-density image).
This symptom can be improved with this function.
ON/OFF* White patch can appear on the heavy paper (the second
side of 2-sided printing) or the coated paper (the first side)
at the tail end of the image. This symptom can be improved
with this function.
T-1-11
Use/Suppl. Service Mode
Change this setting if
Sample G of the faulty
images appears. The
setting of Resolution
should be changed
from 'High Resolution'
to 'High Detail' or
'Hue'.
This setting should be
set to ON if Sample F
of the faulty images
appears.
This setting should be COPIER >
set to ON when Sample ADJUST > V-
D of the faulty images CONT >
appears.
VBACK-Y
,M, C, K
(Level2)
This setting should be COPIER >
set to ON when Sample OPTION >
A (tail end color BODY >
fading) or Sample C VCONT-UP
(white grains) of the (Level2)
faulty images appears.
This setting should be COPIER >
set to ON when Sample OPTION >
B of the faulty images BODY >
appears. ADJ-BLNK
(Level2)
This setting should be COPIER >
set to ON when Sample
OPTION >
E of the faulty images USER > FX-
appears. BC-SW
The setting is possibly COPIER >
set to OFF if Sample H OPTION >
of the faulty images 2TR-RVON
appears. This should be (Level2)
set to ON.
0014-8128