Radwin 5000 HPMP User Manual page 352

Trap Parameters
Table C-3: MIB Traps (Sheet 5 of 6)
Name
swVersionsMatchSoftwareUpgradeRequiredClear
swVersionsCompatibleClear
hssMultipleSourcesDisappearedClear
hssSyncToProperSourceAchievedClear
hssSyncPulseDisappearedClear
tdmBackupClear
linkLockAuthorizedRemoteODU
linkLockAuthorizedODU
linkAuthenticationDisabled
hotStandbyClear
sfpExtraction
sfpPort1Clear
compatibleIdus
desiredRatioCanNotBeAppliedClear
cbwMatch
switchCbwAndChannel
ringRplStateIdle
ringEthServiceStatus
ringFirstRpmReceived
ringEthernetSrviceUnblockedTO
gpsSynchronized
hbsEncryptionClear
hbsEhServiceOpenedToHsu
hbsSynchronizedHsuAlarm
hbsActiveHbs
RADWIN 5000 HPMP User Manual
ID Severity Description
216 normal The trap is sent if SW versions match and SW upgrade is successful.
Contains a single parameter which is its description: 1 - Description:
Software Versions compatible
217 normal The trap is sent if SW versions compatible Contains a single parameter
which is its description: 1 - Description: Software Versions compatible
218 normal Indicates that multiple sync pulse sources disappeared. Contains a
single parameter which is its description: 1 - Description: HSS multiple
sync pulse sources disappeared.
219 normal Indicates that synchronization to a proper Sync source was achieved.
Contains a single parameter which is its description: 1 - Description:
HSS sync pulse - Up.
220 normal Indicates that HSS additional sync pulse disappeared. Contains a single
parameter which is its description: 1 - Description: HSS additional sync
pulse was disappeared.
221 normal Indicates that the TDM main link was activated. Contains a single
parameter which is its description: 1 - Description: TDM main link was
activated.
222 normal Indicates that the remote ODU is authorized. Contains a single
parameter which is its description: 1 - Description: Authorized remote
ODU connection accepted.
223 normal Indicates that the ODU is authorized. Contains a single parameter
which is its description: 1 - Description: Authorized ODU connection
permitted.
224 normal Indicates that the Link Lock is disabled. Contains a single parameter
which is its description: 1 - Description: Link Authentication has been
disabled.
225 normal Indicates that the Primary Link Was Activated. Contains a single
parameter which is its description: 1 - Description: Primary Link Is
Active.
226 normal Indicates that a device was extracted from SFP Port
227 normal Indicates the SFP port 1 status changed to connected. Contains two
parameters: 1 - Description: SFP port 1 status changed to connected -
%s 2 - %s Is the Eth. mode (speed & duplex)
228 normal Indicates that the ODU has identified compatible Idus on both sides of the
link.
229 normal Indicates Current UL/DL Ratio Is Equal To Desired Ratio.
230 normal Indicates that a Channel Bandwidth match was detected. Contains a
single parameter which is its description: 1 - Channel Bandwidth value
in MHz.
231 normal Indicates that the system is switching Channel Bandwidth and channel
frequency. Contains two parameters: 1 - Switching to Channel
Bandwith %n0 MHz and to channel %n1 GHz.
232 normal RPL state changed to Idle.
233 normal Indicates Ethernet service's state - blocked \ unblocked. Contains a
single parameter: 1 - Description: Ethernet's state (blocked \ unblocked)
234 normal Ring application: in non-RPL link indicates first from a specific RPL was
received. Contains a single parameter: 1 - Description: RPM's VLAN ID
235 normal Ring application: in non-RPL link Ethernet service is unblocked due to
RPM timeout.
236 normal Indicates that the GPS is synchronized with satellites.
237 normal Indicates that encryption is OK. Contains a single parameter which is its
description including the HSU's name
238 normal Indicates that encryption is OK. Contains a single parameter which is its
description including the HSU's name
239 normal
Indicates a registered HSU is synchronized.
240 normal Indicates when HBS has been activated.
Release 3.3.30
Appendix C
C-34