Radwin 5000 HPMP User Manual page 341

Private MIB Parameters
Table C-2: Private MIB Parameters (Sheet 19 of 24)
Name
winlink1000IduTdmBackupMode
winlink1000IduTdmBackupCurrentActiveLink
winlink1000IduTdmJitterBufferSize
winlink1000IduTdmJitterBufferDefaultSize
winlink1000IduTdmJitterBufferMinSize
winlink1000IduTdmJitterBufferMaxSize
winlink1000IduTdmJitterBufferSizeEval
winlink1000IduTdmType
winlink1000IduTdmTypeEval
winlink1000IduTdmLineStatusStr
winlink1000IduTdmHotStandbySupport
winlink1000IduTdmDesiredHotStandbyMode
winlink1000IduTdmHotStandbyOperationStatus
winlink1000IduTdmBackupLinkConfiguration
winlink1000IduTdmLineInterfaceConfiguration
winlink1000IduTdmLineImpedanceConfiguratio
n
winlink1000HbsAirState
winlink1000HbsAirOpMode
winlink1000HbsAirAvailTimeSlots
winlink1000HbsAirSectorCbwSupportedStr
winlink1000HbsAirCompressedMon
winlink1000HbsAirConfChanges
winlink1000HbsAirConfTable
winlink1000HbsAirConfEntry
winlink1000HbsAirConfIndex
winlink1000HbsAirConfUpMir
winlink1000HbsAirConfDownMir
winlink1000HbsAirConfHsuName
winlink1000HbsAirConfHsuLocation
winlink1000HbsAirConfDualAntTxMode
RADWIN 5000 HPMP User Manual
OID
1.3.6.1.4.1.4458.1000.3.1.1
1.3.6.1.4.1.4458.1000.3.1.2
1.3.6.1.4.1.4458.1000.3.1.3
1.3.6.1.4.1.4458.1000.3.1.4
1.3.6.1.4.1.4458.1000.3.1.5
1.3.6.1.4.1.4458.1000.3.1.6.1
1.3.6.1.4.1.4458.1000.3.1.6.2.1.1
1.3.6.1.4.1.4458.1000.3.1.6.2.1.2
1.3.6.1.4.1.4458.1000.3.1.6.2.1.3
1.3.6.1.4.1.4458.1000.3.1.6.2.1.4
1.3.6.1.4.1.4458.1000.3.1.6.2.1.5
1.3.6.1.4.1.4458.1000.3.1.6.2.1.6
Release 3.3.30
Type Description
RW TDM backup mode: Enable or Disable where the
main link is the air link or the external link.
Changes will be effective immediatly.
RO TDM backup current active link: N/A
active or external link is active.
RW TDM Jitter Buffer Size.
between the minimum and the maximum TDM Jitter
Buffer Size.
RO TDM Jitter Buffer Default Size. The units are 0.1 x
millisecond.
RO TDM Jitter Buffer Minimum Size. The units are 0.1 x
millisecond.
RO TDM Jitter Buffer Maximum Size. The units are 0.1
x millisecond.
RW TDM Jitter Buffer Size for evaluation.
must be between the minimum and the maximum
TDM Jitter Buffer Size.
millisecond.
RW TDM Type (The value undefined is read-only).
RW TDM Type for evaluation.
RO Line status.
RO Indicates if Hot Standby is supported.
RW Desired Hot Standby Mode.
RO The Link Actual Status.
RW The current configuration of the backup link.
RW TDM Line interface configuration.
RW TDM line impedance configuration (standardT1 -
100Ohm nonStandardT1 - 110Ohm)
Applicable only for T1 TDM type.
Integer RO Holds the state of the HBS.
Integer RW Holds the operation mode of the HBS.
Integer RO This parameter holds the number of available
timeslots (not in use) in the air interface.
DisplayString RO Represents the channel bandwidth which is
supported by the HBS and all connected HSUs.
OctetString RO Holds HBS monitor data in compressed format:
HBS Traffic Monitor In Bytes(4) Out Bytes(4) In
Frames(4) Out Frames(4) HBS State (1) HBS
Freq (4) Number of Links (2) EC Change Counter
(4) Current Ratio (2) Total Air Frames (4) HBS
Rx Rate in Kbps (4) HBS Tx Rate in Kbps (4)
HBS Rx Rate in Fps (4) HBS Tx Rate in Fps (4)
HBS Set Mode (1).
OctetString RO 16 characters that represent 16 HSUs. Each time
a configuration is been changed increment the
relevant character.
N/A Holds the table for all registered HSUs in the sector
(16 entries).
N/A HSUs configuration table entry. INDEX {
winlink1000HbsAirConfIndex }
Integer RO HSUs configuration table index.
Integer RW Uplink MIR towards specific HSU in units of kbps.
Integer RW Downlink MIR towards specific HSU in units of
kbps.
DisplayString RW HSU name.
DisplayString RW HSU location.
Integer RW Spatial multiplexing: MIMO (1) or Diversity (2)
Appendix C
air link is
The value must be
The units are 0.1 x millisecond.
The value
The units are 0.1 x
C-23