Radwin 5000 HPMP User Manual page 349

Trap Parameters
Table C-3: MIB Traps (Sheet 2 of 6)
Name
hssOpStateChangedToINU
hssOpStateChangedToHSM
hssOpStateChangedToHSC
vlanModeActive
spectrumAnalysis
hbsHsuDeregisteredOffline
hbsHsuDeregisteredSuccessfully
hbsHsuRegisteredSuccessfully
hbsHsuRegistrationFailed
hbsHsuViolatedState
hsuViolatedState
hbsUnregisteredSynchronizedHsu
hbsUnregisteredUnsynchronizedHsu
cableQuality
httpAuthentication
telnetAuthentication
tdmServiceAlarm
ethServiceClosed
ethServiceNotPermitted
encryptionAlarm
changeLinkPasswordAlarm
externalAlarmInPort1Alarm
externalAlarmInPort2Alarm
bitFailedAlarm
wrongConfigurationLoadedAlarm
RADWIN 5000 HPMP User Manual
ID Severity Description
19 normal Indicates that the HSS operating state was changed to INU type.
Contains a single parameter which is its description: 1 - Description:
HSS operating state was changed to: INU.
20 normal Indicates that the HSS operating state was changed to HSM type.
Contains a single parameter which is its description: 1 - Description:
HSS operating state was changed to: HSM.
21 normal Indicates that the HSS operating state was changed to HSC type.
Contains a single parameter which is its description: 1 - Description:
HSS operating state was changed to: HSC_DT/HSC_CT.
22 normal Indicates to non-VLAN PC that after 2 minutes the system will support
only VLAN tag on management interface. Contains a single parameter
which is its description: 1 - Description: VLAN Mode is active. Non-VLAN
traffic will be blocked in 2 minutes.
23 normal Indicates that the ODU is in Spectrum Analysis mode. Contains a single
parameter which is its description: 1 - Description: Spectrum analysis in
progress.
24 normal
Indicates that a HSU was deregistered offline (out of link)
25 normal
Indicates that a HSU was deregistered successfully
26 normal
Indicates that a HSU was registered successfully
27 normal Indicates that registration has failed
28 normal
Indicates (on the HBS side) that a HSU is is violated state
29 normal
Indicates (on the HSU side) that the HSU is is violated state
30 normal
Indicates an unregistered HSU has been synchronized.
31 normal
Indicates an unregistered HSU lost synchronization.
32 normal 1Gbps rate is not supported due to bad line quality.
33 normal HTTP Authentication Failure.
34 normal Telnet Authentication Failure.
100 major Indicates that TDM Service is in alarm state. Contains a single
parameter which is its description: 1 - Description: TDM Service - Alarm.
101 major Indicates that Ethernet Service is closed. Contains a single parameter
which is its description: 1 - Description: Ethernet Service is closed.
102 major Indicates that Ethernet Service is not permitted. Contains a single
parameter which is its description: 1 - Description: A valid IDU could not
be detected at %s. Please check your configuration. %s - Is the Local
Site name or Remote Site name or both sides of the Link.
103 major Indicates an encryption key mismatch. Contains a single parameter
which is its description: 1 - Description: Encryption Status - Failed. No
Services are available.
104 major Indicates that a failure has occurred while attempting to change the Link
Password. Contains a single parameter which is its description: 1 -
Description: Failed to change the Link Password at/on: %s. %s - Is the
Local Site name or Remote Site name or both sides of the Link.
105 major The trap is sent every time an alarm occurs in the External Alarm Input of
port #1. Contains a single parameter which is its description: 1 -
Description: External Alarm 1 - <User Text> - Alarm.
106 major The trap is sent every time an alarm occurs in the External Alarm Input of
port #2. Contains a single parameter which is its description: 1 -
Description: External Alarm 2 - <User Text> - Alarm.
107 major The trap is sent if there is no way to recover from the situation.Contains
two parameters: 1 - Description: ODU power up built in test failed. Error
code is: %n 2 - %n number
108 major The trap is sent if there is a way to recover from the situation.Contains
two parameters: 1 - Description: Wrong configuration loaded. Error code
is: %n 2 - %n number
Release 3.3.30
Appendix C
C-31