Table of Contents
Advertisement
www.ti.com
3.7.15 Multichannel Audio Serial Ports (McASP)
Table 3-17. Multichannel Audio Serial Ports Terminal Functions
SIGNAL
NAME
AXR15 / EPWM0TZ[0] / ECAP2_APWM2 / GP0[7]
AXR14 / CLKR1 / GP0[6]
AXR13 / CLKX1 / GP0[5]
AXR12 / FSR1 / GP0[4]
AXR11 / FSX1 / GP0[3]
AXR10 / DR1 / GP0[2]
AXR9 / DX1 / GP0[1]
AXR8 / CLKS1 / ECAP1_APWM1 / GP0[0] / PRU0_R31[8]
AXR7 / EPWM1TZ[0] / PRU0_R30[17] / GP1[15] /
PRU0_R31[7]
AXR6 / CLKR0 / GP1[14] / MII_TXEN / PRU0_R31[6]
AXR5 / CLKX0 / GP1[13] / MII_TXCLK
AXR4 / FSR0 / GP1[12] / MII_COL
AXR3 / FSX0 / GP1[11] / MII_TXD[3]
AXR2 / DR0 / GP1[10] / MII_TXD[2]
AXR1 / DX0 / GP1[9] / MII_TXD[1]
AXR0 / ECAP0_APWM0 / GP8[7] / MII_TXD[0] / CLKS0
AHCLKX / USB_REFCLKIN / UART1_CTS / GP0[10] /
PRU0_R31[17]
ACLKX / PRU0_R30[19]/ GP0[14]/ PRU0_R31[21]
AFSX / GP0[12] / PRU0_R31[19]
AHCLKR / PRU0_R30[18] / UART1_RTS /GP0[11] /
PRU0_R31[18]
ACLKR / PRU0_R30[20] / GP0[15] / PRU0_R31[22]
AFSR / GP0[13] / PRU0_R31[20]
AMUTE / PRU0_R30[16] / UART2_RTS / GP0[9] /
PRU0_R31[16]
(1) I = Input, O = Output, I/O = Bidirectional, Z = High impedance, PWR = Supply voltage, GND = Ground, A = Analog signal.
Note: The pin type shown refers to the input, output or high-impedance state of the pin function when configured as the signal name
highlighted in bold. All multiplexed signals may enter a high-impedance state when the configured function is input-only or the configured
function supports high-Z operation. All GPIO signals can be used as input or output. For multiplexed pins where functions have different
types (ie., input versus output), the table reflects the pin function direction for that particular peripheral.
(2) IPD = Internal Pulldown resistor; IPU = Internal Pullup resistor; CP[n] = configurable pull-up/pull-down (where n is the pin group) using
the PUPDENA and PUPDSEL registers in the System Module. The pull-up and pull-down control of these pins is not active until the
device is out of reset. During reset, all of the pins associated with these registers are pulled down. If the application requires a pull-up,
an external pull-up can be used. For more detailed information on pullup/pulldown resistors and situations where external
pullup/pulldown resistors are required, see the
circuits, see the
Device Operating Conditions
(3) This signal is part of a dual-voltage IO group (A, B or C). These groups can be operated at 3.3V or 1.8V nominal. The three groups can
be operated at independent voltages but all pins withina group will operate at the same voltage. Group A operates at the voltage of
power supply DVDD3318_A. Group B operates at the voltage of power supply DVDD3318_B. Group C operates at the voltage of power
supply DVDD3318_C.
Copyright © 2010–2014, Texas Instruments Incorporated
(1)
TYPE
PULL
NO.
McASP0
A4
I/O
B4
I/O
B3
I/O
C4
I/O
C5
I/O
D4
I/O
C3
I/O
E4
I/O
D2
I/O
C1
I/O
D3
I/O
D1
I/O
E3
I/O
E2
I/O
E1
I/O
F3
I/O
A3
I/O
B1
I/O
B2
I/O
A2
I/O
A1
I/O
C2
I/O
D5
I/O
Device Configuration
section. For electrical specifications on pullup and internal pulldown
section.
Submit Documentation Feedback
Product Folder Links:
AM1808
SPRS653E – FEBRUARY 2010 – REVISED MARCH 2014
POWER
(2)
(3)
GROUP
CP[1]
A
CP[2]
A
CP[2]
A
CP[2]
A
CP[2]
A
CP[2]
A
CP[2]
A
CP[3]
A
McASP0 serial data
CP[4]
A
CP[5]
A
CP[5]
A
CP[5]
A
CP[5]
A
CP[5]
A
CP[5]
A
CP[6]
A
CP[0]
A
McASP0 transmit master clock
CP[0]
A
McASP0 transmit bit clock
CP[0]
A
McASP0 transmit frame sync
CP[0]
A
McASP0 receive master clock
CP[0]
A
McASP0 receive bit clock
CP[0]
A
McASP0 receive frame sync
CP[0]
A
McASP0 mute output
AM1808
DESCRIPTION
Device Overview
37
Advertisement
Table of Contents
