Control Room - Studer Vista 9 Operating Instructions Manual

Vista 9 Digital Mixing System
Talkback and signaling blockdiagram
Studio A
e.g.Speaker
Studio MonitorA

Control Room

Ext 3
(always on)
GPI X Live
Talk to
GPO 6 GPI12
EXT1
Talk to
GPO X GPI13
EXT2
Mic "TB2"
Talk to
Producer
preselected
GPI 7
Legend :
GPI 1
= GPI already configured in .ini files
GPO 2
= GPO already configured in .ini files
= GPI prepared to use, but not
GPI X
assigned to signaling card.
This can be configured in .ini files
= GPO prepared to use, but not
GPO X
assigned to signaling card.
This can be configured in .ini files
1-20 Introduction
Each channel is fitted with a talkback key that activates talkback to the direct
output of the corresponding channel and, if the channel is an N–1 owner, to
the N–1 output.
For details see the talkback and signaling block diagram below.
Ext Location 1
Ret 1
Ext 1
Talk to
CR
( to PFL Speaker)
GPO 1
Vista9 Desk
Studio A
Signaling Keys
Red
Light
GPI 4
SIG1
GPI X
GPI 5
SIG2
GPI X
Talk
Talk to
GPI 6 GPO 4
Studio
A
Talk to
GPI X GPO X
Studio
B
Talk to Talk to Talk to
Aux1 Aux2 Aux3
GPI 8 GPI 9 GPI 10
Relations :
Dim CR and PFL
Dim StudioA
Dim StudioB
Cut StudioA
Cut StudioB
Cut Ext1
Cut Ext2
Sig1 LED StudioA
Sig2 LED StudioA
RedLight StudioA
TalkLED StudioA
Sig1 LED StudioB
Sig2 LED StudioB
RedLight StudioB
TalkLED StudioB
OnAirMode
SW V4.5
using D21m GPIO cards
Studio B
(Line level)
GPI 2
Studio Monitor B
GPO X
GPO X
Studio B
GPO X
Red
Light
GPO 2
SIG1
GPO 3
SIG2
Talk to
Ext1
Talk
TB Keys
GPO 5
Desk Operator
Producer Area (either in control room or in another room)
Talk
to
ChanOut
Grp01
Talk to
Aux4
GPI X GPI X
GPI 11
if: Anytalk in Desk OR ( Anytalk Producer
if: Ret1 Talk to CR AND Ret1 located in Studio
if: Ret2 Talk to CR AND Ret2 located in Studio
if: (Faderstart of source which is assigned to StudioA)
if: (Faderstart of source which is assigned to StudioB)
if: StudioA Cut AND Ret1 located in Studio
if: StudioB Cut AND Ret2 located in Studio
= Sig1OutStudioA OR Sig1InStudioA
= Sig2OutStudioA OR Sig2InStudioA
StudioA Cut OR RedlightStudioA manual
= DeskTalktoStudioA OR Ret1TalktoCR
= Sig1OutStudioB OR Sig1InStudioB
= Sig2OutStudioB OR Sig2InStudioB
= StudioB Cut OR RedlightStudioB manual
= DeskTalktoStudioB OR Ret2TalktoCR
= OnAirKey OR GPI
Ext Location 2
e.g.Speaker
Talk to
CR
( to PFL Speaker)
CR Monitor
Talk to Talk to Talk to
Aux1 Aux2
preselected
Talk to Talk to Talk to
Ext2 Aux3 Aux4
TB Mic
PFL/TB Out
GPO X
TB only
Foot Switch
Talk Channel
to
Mute
ChanOut
Grp N Grp01
GPI X GPI X GPI X
AND Producer located in CR ) [DimLock is activated]
[DimLock is activated]
[DimLock is activated]
OR (StudioA is OnAir)
OR (StudioB is OnAir)
Date printed: 26.10.10
Ret 2
(Line level)
Ext 2
GPI 3
GPI 1
Channel
Mute
Grp N
GPI X
20.09.2010 wp