ADEMCO VISTA-32FB Installation And Setup Manual page 211

PAGER PHONE NUMBER FOR TEST................... 23–9
PAGER PHONE NUMBER FOR TROUBLES........ 23–8
PANIC BUTTON OR SPEEDKEY......................... 23–12
Panic Keys................................................................. 29–5
Partitions..................................................................... 1–2
Perimeter Type 03 .................................................... 21–2
Peripheral Devices ...................................................... 1–3
PERMANENT KEYPAD DISPLAY BACKLIGHTING
............................................................................. 23–13
Phone Access User's Guide....................................... 10–1
Planning a Partitioned System .................................. 2–1
PLL out of Lock ......................................................... 13–3
Polling Loop Current Draw Worksheet ................... 19–3
Polling Loop Expansion .......................................1–1, 7–1
Polling Loop Supervision ............................................ 7–5
Polling Loop Wire Runs .............................................. 7–2
Power Failure............................................................ 30–6
Power Unattained ..................................................... 13–3
POWER UP IN PREVIOUS STATE ........................ 23–3
Power-Up Procedure ................................................. 19–1
PREVENT ZONE XXX BYPASS.............................. 23–5
PRIMARY FORMAT................................................. 23–6
PRIMARY PHONE NUMBER ................................. 23–4
PRIMARY SUBSCRIBER ACCT # .......................... 23–4
PRINTER BAUD RATE ......................................... 23–15
Printer Configurations ............................................. 17–2
Programming Audio Alarm Verification.................. 11–2
Programming Commands........................................... B–2
PROGRAMMING COMMANDS .............................. 20–3
Programming for 4100APG ...................................... 18–3
Programming Partition-Specific Data Fields .......... 20–3
Programming Scheduling Options ........................... 24–6
Programming System-Wide Data Fields ................. 20–3
Programming the Control for the Long Range Radio13–
2
PS24 Power Supply Module ....................................... 1–4
Quick Arm ................................................................. 28–1
QUICK ARM ............................................................. 23–4
Quick Arming ............................................................ 29–2
RANDOMIZE AC LOSS REPORT ........................... 23–2
RCVR SET UP ERROR ............................................ 30–5
REAL TIME CLOCK ................................................ 17–3
Real-Time Clock ........................................................ 27–1
RECEIVER TYPE ................................................... 23–13
Recent Close Report.................................................... 3–2
Recommendations For Smoke And Heat Detectors ...... ii
Regulatory Agency Statements .................................. A–1
Relay commands ..................................................... 24–11
Relay Outputs ............................................................. 9–1
RELAY TIMEOUT XXX MINUTES ...................... 23–15
RELAY TIMEOUT YYY SECONDS ...................... 23–15
Remote Keypad Sounder .......................................... 12–2
Remote Point Modules ................................................ 7–1
Reporting Formats.................................................... 25–1
RESET ON SECOND OFF FOR BELL 1 ............. 23–19
Q
R
RESET ON SECOND OFF FOR BELL 2 ...............23–19
RESTORE REPORT TIMING.................................23–10
Restrict Disarming ....................................................24–2
RF RCVR SUPERVISION CHECK-IN INTERVAL23–
12
RF System Installation Advisories .............................8–3
RF System Operation and Supervision ......................8–2
RF TRANSMITTER CHECK-IN INTERVAL ........23–12
RF TX LOW BATTERY REPORT ENABLE ..........23–12
RF TX LOW BATTERY SOUND ............................23–12
Ring Count .................................................................26–2
RING DETECTION COUNT ....................................23–6
RINGER EQUIVALENCE ......................................... C–1
RJ31X jack .................................................................10–2
Scheduling..........................................................1–5, 24–1
Scheduling Commands ............................................... B–2
Scheduling Menu Mode .............................................24–6
Scheduling Menu Structure ......................................24–7
SECONDARY FORMAT............................................23–6
SECONDARY PHONE NUMBER ............................23–4
SECONDARY SUBSCRIBER ACCT # ...................23–10
SEND CANCEL IF ALARM + OFF ........................23–14
Serial Number Devices ................................................7–2
serial printer ..............................................................18–3
SESCOA ...................................................................... C–1
Sescoa/Radionics ........................................................25–1
SESCOA/RADIONICS SELECT ...............................23–7
Setting Up a Partitioned System ................................2–2
Setup of the 4281/5881 RF Receivers .........................8–3
Specifications .............................................................. C–1
Speed Key [D] Macros................................................29–5
STANDARD/EXPANDED REPORT SECONDARY 23–7
Supervised Fire (Without Verification) Type 09 ......21–2
Supervised RF..............................................................8–5
SUPERVISION PULSES FOR LORRA TRIGGER
OUTPUTS ............................................................23–17
Supervisory Messages ...............................................30–4
SUPERVISORY ON OPEN & SHORT ...................23–18
SUPPRESS TX SUPERVISION SOUND ...............23–14
SWINGER SUPPRESSION ....................................23–10
System Commands ..................................................... B–1
System Communication.............................................25–1
System Defaults.........................................................20–1
SYSTEM LO BAT ......................................................30–5
System LoBat.............................................................30–1
System Messages .......................................................30–5
System Sensor A77-716B EOL Relay Module ............ 6–3
SYSTEM ZONE BYPASS INHIBIT........................23–20
System Zones ...............................................................1–2
Telephone Line Connections .....................................16–1
Telephone Line Supervision......................................16–1
TEMPORAL SIREN PULSE.....................................23–1
Temporary Schedule..................................................24–5
Temporary Schedule Worksheet .............................24–17
Temporary Schedules ..............................................24–17
Index
S
T
Index–5