34PPM
Removal
1)
Remove the COVER REAR 500 (PL10.2.21). (RRP10.9)
2)
Remove the COVER REAR (PL1.1.3). (RRP1.1)
3)
Remove the FUSER ASSY (PL8.1.20). (RRP8.8)
4)
Remove the COVER LEFT (PL1.1.6). (RRP1.3)
5)
Remove the COVER RIGHT (PL1.1.4). (RRP1.2)
6)
Remove the COVER EXIT 500 (PL10.1.1). (RRP10.1)
7)
Remove the 500 EXIT ASST (PL10.1.2). (RRP10.2)
8)
Remove the COVER TOP (PL1.1.7). (RRP1.4)
9)
Remove the COVER FRONT (PL1.1.5). (RRP1.5)
10) Remove the BTR ASSY (PL8.1.21). (RRP8.10)
11) Remove the DUCT FRONT (PL8.1.4). (RRP8.2)
12) Remove the ROS ASSY (PL8.1.1). (RRP8.1)
Never give any impact to the ROS ASSY with a screwdriver or other tools.
13) Remove the SHIELD PLATE ROS (PL8.1.3). (RRP8.3)
14) Remove the GUIDE TRAY LEFT (PL7.1.7). (RRP7.8)
15) Remove the MOTOR COVER (PL11.1.1). (RRP11.1)
16) Remove the SHIELD PLATE LVPS (PL12.1.3). (RRP12.1)
17) Disconnect the connector (P/J43) of the MAIN MOTOR from the LVPS (PL12.1.5).
18) Lift up the 150 FEEDER ASSY (PL6.1.12).
Althrough the 150 FEEDER ASSY clicks into midway when lifted up, push it a little
bit further.
19) Remove the 3 screws (gold, 6mm) securing the MAIN MOTOR to the frame.
20) Remove the MAIN MOTOR.
Replacement
1)
Install the MAIN MOTOR to the frame using the 3 screws (gold, 6mm).
2)
Connect the connector (P/J43) of the MAIN MOTOR to the LVPS (PL12.1.5).
3)
Install the SHIELD PLATE LVPS (PL12.1.3). (RRP12.1)
4)
Install the MOTOR COVER (PL11.1.1). (RRP11.1)
5)
Install the GUIDE TRAY LEFT (PL7.1.7). (RRP7.8)
6)
Install the SHIELD PLATE ROS (PL8.1.3). (RRP8.3)
7)
Install the ROS ASSY (PL8.1.1). (RRP8.1)
Never give any impact to the ROS ASSY with a screwdriver or other tools.
8)
Install the DUCT FRONT (PL8.1.4). (RRP8.2)
9)
Install the COVER FRONT (PL1.1.5). (RRP1.5)
10) Install the COVER TOP (PL1.1.7). (RRP1.4)
11) Install the500 EXIT ASST (PL10.1.2). (RRP10.2)
12) Install the COVER EXIT 500 (PL10.1.1). (RRP10.1)
13) Install the COVER RIGHT (PL1.1.4). (RRP1.2)
14) Install the COVER LEFT (PL1.1.6). (RRP1.3)
15) Install the FUSER ASSY (PL8.1.20). (RRP8.8)
Chapter 3 Removal and Replacement Procedures (RRPs)
3 – 310