Oki B6200 Maintenance Manual page 26

Chain Link Fault Items
004 363 Main Motor fail of rotation
004 922 No Toner
006 335 ROS Motor fail of rotation
Option Tray
007 313
4cCommunucation Fail
Tray 1 Paper Size
007 950 Mismatch (length slows
scan direction error)
Tray 2 Paper Size
007 951 Mismatch (length slows
scan direction error)
Tray 3 Paper Size
007 952 Mismatch (length slows
scan direction error)
Tray 4 Paper Size
007 953 Mismatch (length slows
scan direction error)
Feed Jam 1(Early Feed
008 153
Jam)
008 155 Regi Sensor On Jam
008 156 Regi Sensor Off Jam
Tray 1 Regi Sensor On
008 176
Jam
008 180 Dup Miss Feed Jam
I/F trouble between
008 314
HVPS/MCU PWB-DM
009 413 Toner Black 1 Near Empty
EP Cartridge Type
009 909
Missmatch
009 910 EP Cartridge Not Installed
Conditions of detect/Methods of treatment
Main Motor fail of rotation
Power OFF and /ON.
Replace Main Motor.
Time to change drum/toner cartridge
Change drum/toner cartridge
Revolution of ROS Motor doesn' t become the correct ones for 15sec
and 2sec while Warm Up and Run, respectively.
Defect of ROS Motor(ROS Assy)
Disconnection of wires from MCU PWB J14 to ROS Assy J140 or
loose connection.
The response of communication with RemoteCPU is error. Check the
connection to Option Tray 4.
Defect that the length (slows scan direction) of paper fed from Tray 1/
2/3/4 is different form the specified length by measuring with REGI.
Sensor.
Slip of paper feeding roll, wear, fail of rotation
Wear of paper feeding gear, jumping, fail of rotation
Dirt or defect of REGI. Sensor
REGI. Clutch slip, operational falure
Paper is fed to Regi too fast.
Check paper set, dirt or defect of REGI. Sensor
Regi Sensor is On while Warming up.Scrap of paper is left, dirt or
defect of REGI. Sensor
Paper is not fed from Reg position to Fuser position within the
specified time.
Slip of REGI. Roll, wear, fail of rotation
Breakage failure of Fuser drive gear
Dirt or defect of REGI. Sensor
Regi Sensor doesn' t become On though the specified time is passed
after starting Tray1 Feed
Slip of Tray 1 Feed Roll, wear, fail of rotation
Clutch Assy PH(TRAY1) defects
Dirt or defect of REGI. Sensors
Sensor DUP doen' t become ON when Duplex feeding.
Slip of Feed Roll, wear, fail of rotation
Dirt or defect of Sensor DUP
Disconnect Duplex Unit after powering on
Check the connection of Duplex Unit and machine
Black Toner is almost empty. (No service work)
Change drum/toner cartridge as needed.
ID in NVM of IOT machine and ID of drum/toner cartridge are different.
Set the correct drum/toner cartridge.
The drum/toner cartridge is not set.
Set the drum/toner cartridge correctly.
1 - 10
Chapter 1 Troubleshooting
Ref FIP
FIP1.5
FIP1.16
FIP1.2
FIP1.25
(Separate
volume)
FIP1.14
FIP1.23
(Separate
volume)
FIP1.10
FIP1.9
FIP 1.9
FIP 1.10
FIP 1.9
FIP 1.10
FIP 1.9
FIP 1.10
FIP1.27
(Separate
volume)
FIP1.32
(Separate
volume)
FIP1.11