Oki B6200 Maintenance Manual page 378

34PPM
Removal
1) Remove the COVER REAR 500 (PL10.2.21). (RRP10.9)
2) Remove the COVER REAR (PL1.1.3). (RRP1.1)
3) Remove the COVER LEFT (PL1.1.6). (RRP1.3)
4) Remove the COVER RIGHT (PL1.1.4). (RRP1.2)
5) Remove the COVER EXIT 500 (PL10.1.1). (RRP10.1)
6) Remove the 500 EXIT ASSY (PL10.1.2). (RRP10.2)
7) Remove the COVER TOP (PL1.1.7). (RRP1.4)
8) Remove the COVER FRONT (PL1.1.5). (RRP1.5)
9) Remove the FUSER ASSY (PL8.1.20). (RRP8.8)
10) Remove the BTR ASSY (PL8.1.21). (RRP8.10)
11) Remove the GUIDE TRAY LEFT (PL7.1.7). (RRP7.8)
12) Remove the DUCT FRONT (PL8.1.4). (RRP8.2)
13) Remove the ROS ASSY (PL8.1.1). (RRP8.1)
Never give any impact to the ROS ASSY with a screwdriver or other tools.
14) Remove the SHIELD PLATE ROS (PL8.1.3). (RRP8.3)
15) While lifting up the 150 FEEDER ASSY, remove the MOTOR COVER (PL11.1.1). (RRP11.1)
16) Remove the SHIELD PLATE LVPS (PL12.1.3). (RRP12.1)
17) Remove the connector (P/J4647) of the HARNESS ASSY FUSER (PL8.1.17) from the frame.
18) Remove the harness clamper which holding the HARNESS ASSY FUSER attached to the GUIDE
CRU LEFT to the frame.
19) Disconnect the connector (P/J141) of the INTERLOCK S/W 5V from the HARNESS ASSY LVPS
(PL12.1.1).
20) Disconnect the connector (P/J45) of the INTERLOCK S/W 24V from the LVPS (PL12.1.5).
21) Disconnect the connectors (P/J46 and P/J47) of the HARNESS ASSY FUSER from the LVPS.
22) Remove the 3 screws (gold, 6mm) securing the GUIDE CRU LEFT to the frame.
23) Remove the GUIDE CRU LEFT from the frame.
When removing GUIDE CRU LEFT, pressing LINK GEAR 3 in the direction of the
arrow helps to remove GUIDE CRU LEFT easily.
Replacement
1) Install the GUIDE CRU LEFT to the frame.
When installing, make sure that the LEVER LINK (PL8.1.29) is attached to the
GUIDE CRU LEFT.
2) Install the GUIDE CRU LEFT to the frame using the 3 screws (gold, 6mm).
After installing the GUIDE CRU LEFT, touch the LINK GEAR 3 with your finger.
Make sure that your finger can feel the LINK GEAR 3 move inward, when the LEVER
LINK is pulled up.
3) Connect the connectors (P/J46 and P/J47) of the HARNESS ASSY FUSER to the LVPS
(PL12.1.5).
4) Connect the connector (P/J45) of the INTERLOCK S/W 24V to the LVPS.
5) Connect the connector (P/J141) of the INTERLOCK S/W 5V to the HARNESS ASSY LVPS
(PL12.1.1).
Chapter 3 Removal and Replacement Procedures (RRPs)
3 – 214