Oki B6200 Maintenance Manual page 28

Chain Link Fault Items
012 953 FaceUP Tray Close
012 969 IOT Center Tray Full
016 450 Same SMB host name
016 452 Same IP address
Fail to acquire IP DHCP
016 453
server
016 460 HDD Full
SMTP Server Address
016 500
Resolution Fail for Mail IO
POP Server Address
016 501
Resolution Fail for Mail IO
POP Authentication Fail
016 502
for Mail IO
SMTP Server Address
016 503 Resolution Fail for
Redirector
POP Server Address
016 504 Resolution Fail for
Redirector
POP Authentication Fail
016 505
for Redirector
016 701 Out of Art EX Memory
016 702 Cannot Compress at all
Email Received To Invalid
016 703
Box
016 704 Mailbox is Full
Secure Print Storage
016 705
without HD
Max. User Number
016 706
Exceeded
016 707 Sample Print Fail
016 709 ART EX Command Error
016 710 Delayed Print Fail
Conditions of detect/Methods of treatment
Detect that Faceup Tray is closed though printing out to Faceup Tray is
specified.
Dirt or defect of Sensor Face Up Open
Detect paper left in the offset ejecting tray.
Remove paper in IOT Face Down Tray.
Dirt or defect of Sensor Full Stack
The same host names of PCs exist on the network.
Change host name.
The same IP address of PCs exist on the network.
Check and change the IP address.
Fail to acquire IP address from DHCP server.
Set IP address. (Do not acquire from DHCP)
When accessing HD, Detect HDD Full status.
Enter the Diag Program Hard Disk, and examine the trouble of DC355
Hard Disk.
SMTP server name is not correct.
Set SMTP server name correctly or set by IP address.
POP3 server name is not correct.
POP3 server name correctly or set by IP address.
The certification information (user name and password) of POP3 is not
correct.
Set the certification information (user name and password) of POP3.
SMTP server name is not correct.
Set SMTP server name correctly, or check the setting of DNS server.
POP3 server name is not correct.
POP3 server name correctly, or check the setting of DNS server.
The certification information (user name and password) of POP3 is not
correct.
Set the certification information (user name and password) of POP3.
Detect insufficient memory for PLW process when using ART EX.
Print with low resolution if it is possible. (Print mode [normal])
Printing ART EX is not available due to the lack of print page buffer.
Print with low resolution. (Print mode [normal])Add memory.
Add print page buffer.
Use page printing mode.
When receiving E-Mail, unopened or invalid personal box number is
specified.
Send e-mail to the valid personal box.
Open the new personal box.
Detect personal box full (it reaches the maximum number of messages
in one box. (Job end)
Delete unnecessary message, and start the job again.
Fail to resister the security print because HDD is not installed.
Check that HDD is installed.
Over the maximum number of users of security/sample print.Delete
unnecessary message and registered users of security print, and print
again.
Fail to register sample print because HDD is not installed or it is failure.
Check that HDD is installed.
Enter the Diag Program Hard Disk, and examine the trouble of DC355
Hard Disk.
When processing PLW, ART EX command error causes.
Cancel the job, and execute the job again.
Delete the condition to make impossible Delay Print.(Install HD and so
on)
1 - 12
Chapter 1 Troubleshooting
Ref FIP
FIP1.43
(Separate
volume)
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-