Oki B6200 Maintenance Manual page 391

24PPM
Removal
1) Remove the COVER REAR 250 (PL9.1.12). (RRP9.5)
2) Remove the COVER REAR (PL1.1.3). (RRP1.1)
3) Remove the FUSER ASSY (PL8.1.20). (RRP8.8)
4) Remove the COVER LEFT (PL1.1.6). (RRP1.3)
5) Remove the COVER RIGHT (PL1.1.4). (RRP1.2)
6) Remove the CHUTE ASSY EXIT 250 (Reference Only) (PL9.1.14). (RRP9.7)
7) Remove the CHUTE LW EXT2 ASSY (PL9.1.2). (RRP9.1)
8) Remove the COVER TOP (PL1.1.7). (RRP1.4)
9) Remove the COVER FRONT (PL1.1.5). (RRP1.5)
10) Remove the BTR ASSY (PL8.1.21). (RRP8.10)
11) Remove the GUIDE TRAY LEFT (PL6.1.7 or PL7.1.7). (RRP6.8 or RRP7.8)
12) Remove the DUCT FRONT (PL8.1.4). (RRP8.2)
13) Remove the ROS ASSY (PL8.1.1). (RRP8.1)
Never give any impact to the ROS ASSY with a screwdriver or other tools.
14) Remove the SHIELD PLATE ROS (PL8.1.3). (RRP8.3)
15) Remove the MOTOR COVER (PL11.1.1). (RRP11.1)
16) Remove the SHIELD PLATE LVPS (PL12.1.3). (RRP12.1)
17) Remove the GUIDE CRU LEFT (PL8.1.15). (RRP8.4)
18) Remove the COVER GUIDE CRU (PL8.1.16) and HARNESS ASSY FUSER (PL8.1.17) from the
GUIDE CRU LEFT. (RRP8.7)
19) Remove the INTERLOCK S/W 24V (PL8.1.11) and INTERLOCK S/W 5V (PL8.1.12). (RRP8.5)
20) Remove the SPRING SL (PL8.1.9) from the GUIDE CRU LEFT (PL8.1.15).
21) Remove the SPACER SS (PL8.1.8) from the GUIDE CRU LEFT.
22) Remove the GUIDE SL (PL8.1.7) from the GUIDE CRU LEFT.
23) Remove the LEVER GUIDE from the GUIDE CRU LEFT.
Replacement
1) Install the LEVER GUIDE to the GUIDE CRU LEFT (PL8.1.15).
2) Install the GUIDE SL (PL8.1.7) to the GUIDE CRU LEFT.
3) Install the SPACER SS (PL8.1.8) to the GUIDE CRU LEFT.
4) Install the SPRING SL (PL8.1.9) to the GUIDE CRU LEFT .
5) Install the INTERLOCK S/W 24V (PL8.1.11) and INTERLOCK S/W 5V (PL8.1.12). (RRP8.5)
6) Install the COVER GUIDE CRU (PL8.1.16) and HARNESS ASSY FUSER (PL8.1.17) to the
GUIDE ASSY CRU L. (RRP8.7)
7) Install the GUIDE CRU LEFT (PL8.1.15). (RRP8.4)
When installing, make sure that the LEVER LINK (PL8.1.29) is attached to the
GUIDE CRU LEFT.
After installing the GUIDE CRU LEFT, touch the LINK GEAR 3 with your finger.
Make sure that your finger can feel the LINK GEAR 3 move inward, when the LEVER
LINK is pulled up.
8) Install the SHIELD PLATE LVPS (PL12.1.3). (RRP12.1)
9) Install the MOTOR COVER (PL11.1.1). (RRP11.1)
10) Install the SHIELD PLATE ROS (PL8.1.3). (RRP8.3)
Chapter 3 Removal and Replacement Procedures (RRPs)
3 – 227